Tyresöstöttan
Tyresöstöttan -ryhmän tuotteet
Tilted sailboat support. Adjustable height 110-155cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.
Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.
Number of supports: recommendation according to boat length below
- >25 feet 4 pcs
- 25-30 feet 6 pieces
- 30-40 feet 6-8 pieces
- 40-55 feet 8-10 pieces or more
- Tilted support leg
- Adjustable height 110-155cm
- Easy and quick height adjustment
- Assembled
- Material: galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCFG 110
- Made in Sweden
Vertical boat support made of hot-dip galvanized steel. Adjustable height 75-105cm. Quick height adjustment with trapezoidal thread and wing nut. Large, rectangular rubber-coated frame support made of painted marine plywood. The support adapts to the bottom of the boat, but if you have a boat with a deep V-bottom you can use two vertical motorboat support legs at the stern and two tilted sailboat support legs at the bow. The supports are stackable to minimize storage space.
- The recommendation is two supports per 8-10 feet of length.
- The weight and support of the boat should be on the keel strip
- Always use chains between supports
Number of supports: recommendation according to boat length below
- >30 feet 4 pcs
- 30-45 feet 6 pieces
- 45< feet 8 pieces or more
- Vertical support leg
- Adjustable height 75-105cm
- Maximum load per support: 3600kg
- Easy and quick height adjustment
- Assembled
- Material: hot-dip galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCMG 750
Vertical boat support made of hot-dip galvanized steel. Adjustable height 60-90cm. Quick height adjustment with trapezoidal thread and wing nut. Large, rectangular rubber-coated frame support made of painted marine plywood. The support adapts to the bottom of the boat, but if you have a boat with a deep V-bottom you can use two vertical motorboat support legs at the stern and two tilted sailboat support legs at the bow. The supports are stackable to minimize storage space.
- The recommendation is two supports per 8-10 feet of length.
- The weight and support of the boat should be on the keel strip
- Always use chains between supports
Number of supports: recommendation according to boat length below
- >30 feet 4 pcs
- 30-45 feet 6 pieces
- 45< feet 8 pieces or more
- Vertical support leg
- Adjustable height 60-90cm
- Maximum load per support: 3600kg
- Easy and quick height adjustment
- Assembled
- Material: hot-dip galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCMG 600
Tilted sailboat support. Adjustable height 190-235cm. Foldable. Powder coated steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.
Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.
Number of supports: recommendation according to boat length below
- >25 feet 4 pcs
- 25-30 feet 6 pieces
- 30-40 feet 6-8 pieces
- 40-55 feet 8-10 pieces or more
- Tilted support leg
- Adjustable height 190-235cm
- Easy and quick height adjustment
- Assembled
- Material: powder-coated steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCF 190
- Made in Sweden
Tilted sailboat support. Adjustable height 170-215cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.
Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.
Number of supports: recommendation according to boat length below
- >25 feet 4 pcs
- 25-30 feet 6 pieces
- 30-40 feet 6-8 pieces
- 40-55 feet 8-10 pieces or more
- Tilted support leg
- Adjustable height 170-215cm
- Easy and quick height adjustment
- Assembled
- Material: galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCFG 170
- Made in Sweden
- Sturdy structure
- Withstands high loads relative to its own weight
- Quick and easy height adjustment (trapezoidal thread with large wing nut)
- Maintenance-free, large articulated frame plate with profiled frame protection made of high-quality rubber
- Hot-dip galvanized (stainless steel screw/lock nut)
- Easy to disassemble for storage and transport
- Long service life, does not require large summer versions
- Delivered unassembled
- Quick release fasteners for safety chain
Vertical boat support made of hot-dip galvanized steel. Adjustable height 90-120cm. Quick height adjustment with trapezoidal thread and wing nut. Large, rectangular rubber-coated frame support made of painted marine plywood. The support adapts to the bottom of the boat, but if you have a boat with a deep V-bottom you can use two vertical motorboat support legs at the stern and two tilted sailboat support legs at the bow. The supports are stackable to minimize storage space.
- The recommendation is two supports per 8-10 feet of length.
- The weight and support of the boat should be on the keel strip
- Always use chains between supports
Number of supports: recommendation according to boat length below
- >30 feet 4 pcs
- 30-45 feet 6 pieces
- 45< feet 8 pieces or more
- Vertical support leg
- Adjustable height 90-120cm
- Maximum load per support: 3600kg
- Easy and quick height adjustment
- Assembled
- Material: hot-dip galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCMG 900
Tilted sailboat support. Adjustable height 130-175cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.
Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.
Number of supports: recommendation according to boat length below
- >25 feet 4 pcs
- 25-30 feet 6 pieces
- 30-40 feet 6-8 pieces
- 40-55 feet 8-10 pieces or more
- Tilted support leg
- Adjustable height 130-175cm
- Easy and quick height adjustment
- Assembled
- Material: galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCFG 130
- Made in Sweden
3m chain for the support legs. The support legs of the Tyresöstötta have a slot where the chain can be attached.
- Chain 3m
- Material: galvanized steel
- For attaching support legs to each other
- NOTE! All support legs must be connected to each other with a chain
- The best way is to attach the chain, then push the supports outwards to tighten the chain. It is difficult to tighten the chains after they are installed.
"Hot-dip galvanized steel top plate with stainless bolt and nut for sailboat and motorboat supports. Upholstered with hull protection made of EPDM rubber.
Suitable for MBS and SBS supports, but also for other similar support models on the market.
It is recommended to replace it if, for example, your old wooden top plate is broken.
Dimensions: 255x255 mm.
- Suitable for MBS and SBS support legs
- Frame protection
- 255x255mm
Tilted sailboat support. Adjustable height 150-195cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.
Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.
Number of supports: recommendation according to boat length below
- >25 feet 4 pcs
- 25-30 feet 6 pieces
- 30-40 feet 6-8 pieces
- 40-55 feet 8-10 pieces or more
- Tilted support leg
- Adjustable height 150-195cm
- Easy and quick height adjustment
- Assembled
- Material: galvanized steel
- Adaptive supports
- Rubber-coated ball base
- Manufacturer's product code: LCFG 150
- Made in Sweden
"Hot-dip galvanized steel top plate with stainless bolt and nut for motorboat supports. Covered with a hull protector made of EPDM rubber. Due to its narrow design, the top plate fits better against the hull compared to a traditional square top plate.
Suitable for MBS supports, but also for other similar support models on the market.
It is recommended to replace it if, for example, your old wooden top plate is broken.
Dimensions: 310x160 mm.
- MBS-For support legs
- Frame protection
- 310x160mm
