Boat care products

Star brite soot drain remover removes black drains caused by water, soot and dirt and cleans soot around the exhaust tip.
Spray directly onto black stains and wipe away, no brushing required.
Hundreds of uses: instantly removes stains from boats, cars, caravans and houses.

General washing of the boat sides

Washing the sides of a boat can be challenging, as dirt that has been picked up by the water often becomes caked in. It is naturally easier to wash the sides when the boat is on land. In that case, the sides are usually washed with stronger agents and a pressure washer. It is always a good idea to wash the sides and bottom as soon as possible after lifting the boat, before the dirt has a chance to dry.

Washing the waterline while the boat is on land is best done with Star brite Hull and Waterline Power Wash. This Hull Cleaner very effectively removes yellowing of the waterline, algae, slime deposits, rust stains and other dirt from the entire hull of the boat. The product does not require scrubbing and does not contain acids that damage the hull of the boat. Its composition is a carefully designed and tested combination of various ingredients, including oxalic acid. Homemade oxalic acid mixtures have the risk that they are too strong and break the gelcoat surface. If the surface is broken, dirt can penetrate even deeper in the future and is more difficult to remove by washing. The buffered composition of Hull Cleaner does not damage the surface of the boat's side to be cleaned and is ideal when preparing to polish the hull. If the boat is washed on a boat trailer, the trailer must be protected from detergent. The power wash of the hull and waterline is so strong that it removes waxes. Therefore, this product is not recommended for waxed surfaces during the boating season.

If the surface of the boat's side has been broken or rubbed off (or if too strong and incorrect detergents have been used), it must be treated with an abrasive polishing fluid or paste. Polishing fluids can be used to remove the damaged Gelcoat surface and restore the shine. If the Gelcoat surface is only faded by UV radiation or the scratches are light, Star brite polishing wax can be used. This product contains abrasive particles and wax in the same product. It therefore does not require any further treatment. Star brite polishing wax is unique in boating.

Washing the sides of the boat during the season when the boat is in the water is more challenging. It is important to note that the detergent does not use a wax-removing agent. It is also a good idea to consider the fate of the washing water. When the boat is in the water, the washing water naturally ends up in the water. In this case, it is good for the detergent to have as little environmental impact as possible. For this purpose, Star brite has biodegradable products. The boat detergent concentrate is a great product for this purpose. It is plentiful and does not burden the environment. Star brite Boat detergent concentrate can also be used to wash other parts of the boat during the season. It is also worth checking out Star brite's Sea Safe series, whose products are effective, economical, fully biodegradable and environmentally friendly cleaning agents. Phosphate-free detergents are a much better alternative for the water. These "green" products also come in biodegradable bottles.

When washing the sides, black streaks and soot stains that appear on the sides can also be treated well. These stains are challenging, because soot, for example, effectively penetrates deep into the unprotected surface. For this reason, an acid-free detergent has been developed that is also effective on soot. Star brite Black streaks and soot stains cleaner is effective and it is worth cleaning the area around the exhaust pipe end regularly with it.

Regardless of where or when you wash the side of your boat, it is always a good idea to protect the surface with wax at the end. A protected surface will stay clean and neat looking for much longer. High-quality waxes also provide protection against the sun's UV radiation. When the boat is on land, we recommend using Star brite High-Quality Boat Polish or Star brite Cleaning Boat Polish/Wax. These products are also suitable for seasonal protection of the deck parts of the boat that are not used for transportation. When the boat is in the water, you can protect the sides with Star brite Quick Wax or Star brite Wax Wash.

INSTRUCTIONS

Spray directly onto dirty surface. Leave for 30 seconds, then wipe away with a clean cloth, brush or sponge. Rinse thoroughly with clean water. Heavily soiled surfaces may require a second application and light brushing. Biodegradable formula will not remove wax or polish, safe to use on fiberglass, vinyl, plastic, rubber, metal and painted surfaces.

Star brite canopy cleaner is developed to effectively remove grease, fish blood, food spills and other stains without damaging the surface.

The cleaning agent's PTEF polymers adhere to the treated area and prevent dirt from adhering and harmful UV rays. The product is suitable for both small spills and larger areas. It is simple to use: spray, leave to act and rinse. The product can be used, for example, on boats, cars and motorhomes/caravans. It is well suited for, for example, Sunbrella®, Dacron®, polyester and sailcloth.

• 500ml – bottle
• 650ml – spray
• 1 L – spray

DIRECTIONS FOR USE: For cleaning individual stains: apply directly to the stain and allow to absorb for 30 seconds. Gently rub the stain with a cloth, sponge or soft brush. Rinse thoroughly with clean, fresh water. For cleaning large areas: apply evenly to the entire area to be cleaned and allow to absorb for 30-60 seconds. Gently rub the area with a cloth, sponge or soft brush to remove the dirt. Rinse thoroughly. Stubborn stains may require multiple applications and a longer absorption time. Note: Test the product on a hidden area first to make sure it does not change the color of the fabric. Do not use the product if it leaves marks on the fabric.

ANVISNINGAR: Rengör genom att applikata direkt på äcken och let verka i 30 secunder. Använd en trasa, svamp eller mjuk borste och gnugga prudjanat. Rinse carefully with rent vatten. Clean large areas of the genome and apply it evenly over the whole surface so that it is clean and let it dry for 30 seconds until 1 minute. Gnugga prudjanat areat med en trasa, svamp eller mjuk borste så att smutsen lyfts bort innan hela areatt sköljs grundligt. Envisa äckar kan nekrama ektetada behandeling och langger behandlingstid. Note! Test the färgbeständigheten på ett visible area. Använd inte om färgbeständigheten äpää.

Star brite Teak Cleaner + Brightener cleans and brightens teak in one go (step 1 + step 2), saving you time and effort. The powerful formula quickly prepares the surface for oiling. Ideal for use on all woods, decks and furniture. Biodegradable.

DIRECTIONS FOR USE: For heavily soiled or weathered surfaces, apply the product directly to dry wood. Use a coarse brush to spread the product throughout. Leave to work in for an average of two to three minutes before brushing. Brush in the grain of the wood to ensure a deep clean before rinsing with clean water. Heavily soiled surfaces may require a second treatment. If the wood is only slightly soiled, apply the product to a damp surface. Brush lightly in the grain of the wood and rinse thoroughly with clean water. After cleaning, use teak oil to restore the natural color and tone and to protect the surface. Rinse spills immediately from surfaces that you do not want to treat. Avoid contact with fabrics.

Star brite Super Spray is an effective all-purpose cleaner for boats, caravans, service stations, offices and households.

All-purpose; especially removes grease, oil, fish blood stains. Simple to use; spray, wipe away dirt. Biodegradable Several service shops in Finland trust the effectiveness of Super Spray's all-purpose cleaner and use it in their everyday operations.

Instructions:

Spray onto the area to be treated, then spread the product thoroughly using a sponge, brush or rag. Leave to work for 15-30 seconds before lightly brushing or wiping. Rinse with fresh or salt water. Stubborn dirt may require re-treatment, in which case the product should be left to work for a minute before scrubbing and rinsing.

NOTE: Before treating the entire area, test the product on a small area or on an area where it may drip. If no adverse reaction occurs, do not use the product on that surface. Some painted surfaces may fade colors.

Star brite stain remover effectively cleans and removes sea pox (stain) from boat hulls and traction devices. Also effectively removes sea / lake dirt from rubber and RIB boats. Excellent for fiberglass, wood and iron surfaces. Spray on dry hull, allow to act and rinse. Special patented product.

Washing the bottom of the boat
The bottom of the boat is often the dirtiest place to wash it. All sorts of dirt has accumulated there from the water during the season. In addition to dirt, sea lice (sea pox) are also a nuisance in marine areas. Removing them without a proper detergent is almost impossible. Even when washing with a pressure washer, the bottom of the sea lice will stick to the boat. Removing sea lice is not only a matter of appearance, as sea lice also slow down the boat's speed and increase fuel consumption in fuel-powered boats.

Star brite tar remover effectively cleans and removes sea pox (tar) from boat hulls and traction devices. Also effectively removes sea / lake dirt from rubber and RIB boats. Excellent for fiberglass, wood and iron surfaces. The product is easy to use: spray on a dry hull, let it work and rinse. Remember to wear protective equipment and follow the instructions for use.

Another effective product for bottom cleaning is Hull and bottom cleaner Ez-on Ez-off. The advantage of this product is that it also works well in cooler weather. Therefore, it is well suited for Finnish spring and autumn (and sometimes, unfortunately, summer). Star brite hydrochloric acid-based hull and bottom cleaner Ez-on Ez-off cleans the hull of the boat from vegetation, slime and seaweed, etc. The product is buffered, so it is safer than many other acid-based boat bottom cleaning products. Suitable for fiberglass, wood and iron surfaces. Remember to wear safety equipment and follow the instructions for use!

When washing the bottom, there is one important thing to remember. In marine areas, the bottoms of most boats are painted with antifouling paint (toxic paint). This paint is not at all healthy for humans either when the substance comes into contact with the skin or when inhaled into the lungs. For this reason, the antifouling surface should never be brushed or sanded dry. Always moisten the surface of the toxic paint properly before starting work.

Instructions

Washing and protecting the boat's canopy and fabrics

Instructions

Star brite hydrochloric acid-based hull and bottom cleaner Ez-on Ez-off cleans the hull of the boat from vegetation, slime and seaweed, etc. The product is buffered, so it is safer than other acid-based boat bottom cleaning products. Suitable for fiberglass, wood and iron surfaces. Also works well in cooler washing conditions. Always finish the surface with an appropriate boat wax.



DIRECTIONS FOR USE: Lift the boat out of the water and remove the largest growths. Allow the growths and stains to dry completely. Stains and growths above the waterline can be removed while the boat is in the water. Pour the product into an open plastic container and apply to the dry surface of the hull with a natural bristle brush. Keep the growths and stains wet and foaming with the product. Foaming is an indication that the product is removing the growths. Add product to maintain the foaming. After a few minutes of foaming, most surfaces will be clean and ready to rinse with water. For heavy growth, cleaning may require multiple applications and light scraping.

NOTE: Avoid spilling or splashing on surfaces other than those being treated. Test on a small area of ??aluminum frames before applying. Cover trailer with plastic sheeting to prevent staining or damage to metal surfaces. Rinse spills thoroughly immediately. Product will discolor some primers. Avoid contact with fabrics or carpets. Use caution when transporting to prevent splashing. DO NOT MIX WITH OTHER CLEANERS.

Star brite Hull and waterline power wash (Hull Cleaner) very effectively removes yellowing of the waterline, algae, slime deposits, rust stains and other dirt from the entire hull of the boat. The product does not require rubbing and does not contain acids that damage the hull of the boat. Its composition is a carefully designed and tested combination of different ingredients, including hydrochloric acid. Hull Cleaner has been developed specifically to clean the hull of the boat, as well as bottom vegetation and yellowing of the waterline. It also removes rust, fish blood stains from fiberglass and painted surfaces. Hull Cleaner does not damage the surface being cleaned and is ideal for preparing the hull for polishing. If the boat is washed on a boat trailer, the trailer must be protected from detergent.

INSTRUCTIONS FOR USE: Shake well. Apply using either a sprayer or sponge. Leave on the surface for two to three minutes (2-3min), so that the area to be cleaned does not dry out during the action of the Hull Cleaner, then rinse with clean water. The hull of the boat must be dry and Hull Cleaner is applied undiluted. Heavily soiled surfaces may require a second treatment. For best results, use the product above +10°C. To brighten and protect the cleaned area, use high-quality boat waxes.

Star brite biodegradable detergent concentrate is specially formulated for cleaning fiberglass, metal and painted surfaces.

Cleans the boat's hull, deck, and fittings until they are sparkling clean.
A biodegradable product that can also be used as a basic boat cleaning agent during the season.
Special agents effectively clean dirt, fish blood, salt deposits, waterline dirt, etc.
Safe to use on all boat surfaces.
Does not remove wax or polish.

DIRECTIONS FOR USE: Pour 3 capfuls into 10 liters of water. Mix until foamy and apply.
with a sponge, brush or soft cloth for fiberglass, vinyl, aluminum, teak and
other boat surfaces. Rinse well with water and let dry. Always finish the surface
Star brite boat wax.

Star brite PTEF boat polish is a premium polish/wax that provides the best possible protection for fiberglass, metal and painted surfaces. This premium wax provides an extremely smooth, non-stick surface that effectively repels dirt, oil and stains. The boat polish also reduces friction, so it can also be used on the bottom of boats on hard surfaces (hard paints, propellers, drives). The product is even used on the bottoms of racing boats, due to its excellent adhesion, hold and low friction.

Contains UV protection agents that also prevent fading of surfaces. Also available as a pre-softened paste (85714). The protection provided by the product lasts up to 4-5 times longer than other boat waxes! PTEF offers extreme protection for boats. PTEF is a high-tech polymer that adheres tightly to fiberglass, painted and polished surfaces. It makes the treated surface very durable and provides maximum protection against dirt, oil and other contaminants. A UV and weather-resistant surface is formed on the treated area, which is also resistant to oxidation. PTEF guarantees significantly longer-lasting protection for the surface than other similar polishes or waxes.

INSTRUCTIONS:
Wash the surface clean before polishing (we recommend Star brite Boat Cleaner or Star brite Sea Safe Boat Cleaner). Shake the bottle vigorously. Apply evenly with a clean cloth, small areas at a time, using a circular motion while the polish is wet. Star brite Boat Polish / Wax dries quickly to a dull finish. Wipe the dull area with a second, clean cloth. For best results, apply a second coat within 30 days. Two coats provide excellent protection against fading, scaling, rust, corrosion and general deterioration. Oil, dirt and salt water do not adhere to the highly slippery surface and can be washed off with regular boat cleaner and water.

Star brite deck cleaner removes even the toughest dirt and stains from deep within the pores of the roughening thanks to surfactants. Some dirt gets deeper than more common surface stains and is more difficult to remove. This problem is especially familiar from roughened boat deck surfaces. In this case, we need to use surfactants, chelates. Their molecules surround the dirt molecules and lift the dirt to the surface you are cleaning. This allows them to be washed off with water without damaging the surface.

Star brite deck cleaner not only cleans difficult surfaces, but it also leaves a protective PTFE film on the surface, which is not slippery. The film protects the surface from re-soiling and UV radiation. The product is safe to use because it does not contain strong acids. It does not require hard scrubbing, but it is worth applying the substance with a brush to get it to the entire area of ??the surface to be washed. Excellent for all fiberglass, vinyl, plastic, metal and painted surfaces.



DIRECTIONS FOR USE: Wet the lid. Apply the product to the surface to be treated and brush the area thoroughly. Leave for 2-3 minutes and brush the lid thoroughly and rinse well. Allow the lid to dry. Heavily soiled lids may require a second treatment.

A truly versatile plastic repair agent that removes scratches from acrylic, polycarbonate, sunroofs and many other plastic surfaces. The product can be used on almost all types of plastic and removes tarnish and scratches! Easy to use, rub the agent into the area and wipe away. Cleans stains, salts and surface discoloration.

Always use “step 2” after treatment to protect and polish the surface.
Applications include boat windows, boat cover windows, skylights, plastic shelves, helmet visors, headlights (closed), etc.



INSTRUCTIONS: Shake the bottle vigorously before use. Apply generously to a soft cloth. Apply to the plastic surface in circular, overlapping motions at a 90-degree angle to avoid scratching the surface. Polish the restored surface with a clean, dry cloth to reveal the restored surface.

Star Brite Plastic Surface Polish/Restorer restores shine and clarity to acrylic, polycarbonate, sunroofs and many other plastic surfaces.
The product is easy to use; just apply and rub off. The plastic surface polish removes contaminants from almost all plastic surfaces.
Note: Always use “step 1” material first.



INSTRUCTIONS: Shake the bottle vigorously before use. Apply generously to a soft cloth. Apply to the plastic surface in circular, overlapping motions. Polish the surface lightly with a clean, dry cloth to reveal the shine.

Star brite aluminum boat bottom cleaner/restorer is specially formulated to remove dirt, waterline and bottom vegetation from aluminum boats. The product is biodegradable. A special buffer solution makes this product safer to use than many other similar products without compromising on effectiveness.

FOLLOW THE PRODUCT'S INSTRUCTIONS CAREFULLY!
Because aluminum oxidizes unevenly, heavily oxidized areas require more aggressive cleaning than lightly oxidized areas. Follow these instructions for best results. Failure to follow these instructions will result in an uneven, streaky, or uneven surface. The product requires further treatment with Aluminum Protective Polish (sold separately).

When using Star brite Aluminium Cleaner & Restorer you must:
ALWAYS apply the product evenly with a scrubbing pad.
ALWAYS rinse thoroughly before the product dries.
ALWAYS follow up with Star brite aluminum boat PTFE polish/wax .

SUPPLIES NEEDED:

Before you begin, you will need acid-resistant gloves, safety glasses, Star brite Aluminum Boat Bottom Washer/Restorer, Star brite Medium Scrub Pad (red), Star brite Aluminum Polish, several clean polishing cloths, and water from a hose for rinsing.

Step 1.

To avoid streaks, start at the bottom of the area to be cleaned and work up in small areas at a time. Apply Star brite Aluminum Boat Bottom Cleaner to the surface in even strokes using the fine mist setting on the spray nozzle. The cleaner will foam when it contacts the oxidized area, indicating that it is working.

Step 2.

Use the Star Brite Red Medium Grit Scrubbing Pad to spread the Aluminum Boat Bottom Cleaner into an even, covering layer. Then scrub systematically with even pressure to allow the cleaner to penetrate even the most heavily oxidized areas.

Step 3.

Rinse the cleaned surface thoroughly with clean water. Remember to rinse the surfaces underneath as well. DO NOT allow the cleaner to dry on any surface.

Repeat these steps as needed until the surface is clean. Heavy oxidation may require multiple applications and scrubbing to completely remove. Note that the cleaned surface may still appear uneven until polished.

Next, restore shine with Star brite Aluminum Boat PTFE Polish – Sold separately

Watch the video to learn how to use the product correctly.

The boat window cleaner and protector is an industry first: it enhances visibility in rainy, wet weather.
Designed for use on clear plastic surfaces such as Strataglass, EZ2CY and Eisinglass.
Boat window cleaner and protector is specially designed for surface treatment, removing dirt and oxidation. Powerful polymers repel rain and salt. Provides maximum visibility even in bad weather.

Ultimate View Guard® Clear Plastic Treatment is an industry first: it improves visibility in wet conditions and is specifically designed for clear plastic windows such as Strataglass, EZ2CY® and Eisinglass. Surface treatments remove dirt and grime. Advanced polymers repel rain, salt, splashes and dirt to maximize visibility in harsh weather conditions. Ultimate View Guard® also provides protection from harmful UV rays that can cause clear plastic to crack and yellow.

DIRECTIONS: Spray onto surface and apply in a circular motion with a clean, soft cloth, covering an area of ??approximately 45 x 45 cm at a time. Turn cloth over and wipe completely dry. Do not allow product to dry before wiping. Use as needed. For yellowed, tarnished or lightly scratched plastic openings, use Star Brite Clear Plastic Restorer before applying Ultimate View Guard.

Star brite vinyl protectant (Step 2) restores the appearance and provides UV protection to all vinyl, rubber, plastic and leather surfaces.

Star brite non-toxic spider and bird dropping remover removes dirt effectively and gently. Contains no bleach, safe for children and pets.
Bird and spider stains can be a disfiguring sight on your boat and won't come off with soapy water alone. However, Star Brite's Bird & Spider Stain Remover starts to break them down immediately. The non-abrasive, non-toxic formula won't damage fiberglass or painted surfaces and won't remove wax or polish. The stains break down without the need for harsh scrubbing.

DIRECTIONS FOR USE: Spray liberally directly onto the stain. Allow to soak into the stain for 30-45 seconds, then scrub gently with a boat brush. Rinse thoroughly with clean water. Stubborn or sun-baked stains may require a second application. Test the effect on the color in an inconspicuous area before cleaning the entire surface.

Star brite Boat Polish / Wax is suitable for fiberglass, aluminum, metal and painted surfaces.
Cleans, polishes, protects, gives a deep shine and can also be worked in the sun.
Prevents fading caused by UV rays and lasts up to four times longer than similar products.
Easy to apply by hand or with a low-speed sander.
Does not require vigorous rubbing.

DIRECTIONS FOR USE: Wash the surface to be polished. Shake well. Apply with a steady, continuous motion with a clean cloth. Treat a small area at a time. Rub well to remove limescale, surface rust and oxidation while the polish is wet. Most surfaces do not require vigorous scrubbing. Often calcified surfaces may require more scrubbing. The product dries quickly to a haze. Rub off the haze using a dry cloth and the treated surfaces will shine like new. The product removes limescale from most fiberglass and aluminum surfaces, restoring their original shine. For best results, repeat the treatment within 10-30 days. A second coat removes limescale and oxidation, restoring the surface to its original shine. Two treatments ensure a surface that protects against limescale, rust, corrosion and oxidation for a year or even longer. Foreign substances such as tar, oil and salt do not adhere to the surface and can generally be washed off with water.