Blue Sea

Traditional 4-way 1-2-OFF-BOTH main switch. Can control load or charging between two separate battery banks. Allows two separate battery banks to be connected for charging or emergency starting. Tinned copper connection bolts ensure maximum conductivity and corrosion protection. Connection bolts accept M10 cable lugs. Connection bolts accept M10 cable lugs. 22mm connection bolts allow multiple cable lugs to be mounted on the same connection bolt. Main switch knob is removable. Can be surface or flush mounted.

• Blue Sea 4352 Below Deck is a switch panel for indoor installation. Durable panel with molded frame resistant to UV radiation and salt spray. Easy to install, low profile design makes installation in tight spaces easy. Simple to connect using quick connectors on the circuit breakers. Red "ON" indicator lights ensure visibility even in poor lighting conditions.
  
  FEATURES:
  Illuminated circuit breakers that also function as a switch.
• 6 Carling Technologies™ 15A circuit breakers
• ON indicators
• Polycarbonate/ABS panel surface, UV-resistant, fire-retardant, not susceptible to corrosion
• The RAIL with quick connectors eliminates the need for wire harnesses and messy connections
• Two-wire connection to power supply, #10 ring terminals. Terminals are screwed onto busbars to secure connections
• Comes with 15 name tags, easy to replace. More different name tags for different functions are available from Blue Sea Systems' range
• Stainless steel mounting screws #6 x 5/8 included?

Main switch for bow thruster, anchor winches, etc., remotely controlled via a separate electrical connection. Mechanical on/off switching (100,000 cycles). Manual switch ("lockable") for additional safety in case of power failure or maintenance of the remote control. Output for remote control switch and use of diode indicator.

Clutch: Gas-tight = suitable for the engine compartment.

Switch: Continuous load 500 amps.

Maximum load at start-up: 2500 amps for 10 seconds.

Maximum load over 5 minutes 700 amps.

Own consumption when switched on: 12V=0.10A

Approvals: ISO 8846, SAE J1171, IP66

71257: Remote-controlled power switch

Single-action ON-OFF main power switch for outboard and small inboard boats. Allows individual battery bank to be disconnected from the load. Tinned copper terminal bolts ensure maximum conductivity and corrosion protection. Terminal bolts accept M10 cable lugs. 22mm terminal bolts allow multiple cable lugs to be installed on the same terminal bolt. The main power switch knob is removable. Can be surface or flush mounted.

Product's measurements:

600A continuous load. Fiberglass reinforced nylon. 2 pcs 10mm connection points. All conductive parts are tinned copper.

Illuminated 15A circuit breaker allows you to turn the circuit on and off, provides clear 'ON' indication and protects against overcurrent situations. Cigarette lighter socket and dual 2.1A USB socket. Includes 15 different stickers for attachment.

Installation instructions:

Blue Sea's ready-made charging kit with automatic charging relay and main circuit breaker. Ready-made kit for a max. 120A charger when you want to add a second battery to your boat. The kit includes the 7610 SI-ACR charging relay for a 120A charger and the main circuit breaker 5511e suitable for the kit.

Combines power distribution and line fuses in the same box
• Positive rail equipped with #10-32 pin
• Can be used for 24-hour circuits
• Available in models with or without a lid
• The cover meets ABYC/USCG requirements for insulation and includes an easy-to-open push-button cover that protects the fuses, a slot for two spare fuses, and a label recess that accommodates a Blue Sea Systems Small Format label for easy circuit identification
• Fuse boxes with lids contain 20 labels on which you can write the name of the circuit
• Tinned copper busbar and fuse holders
• Possibility to use ring or fork connectors
• Suitable for fast blade fuses (ATO® and ATC®)
• Fuses available separately

Single-action ON-OFF main switch for two batteries for outboard boats and small inboard boats. This main switch can be used to simultaneously disconnect two completely separate battery banks from the load, the main switch itself does NOT allow two batteries to be connected. The connection bolts made of tinned copper ensure maximum conductivity and corrosion protection. The connection bolts fit an M10 cable lug. The 22mm connection bolts allow the installation of multiple cable lugs on the same connection bolt. The main switch knob is removable. Can be mounted as a surface or flush mount

• Blue Sea 4350 Below Deck is a switch panel for indoor installation. A durable panel with a molded frame that is resistant to UV radiation and salt spray. Easy to install, low profile design makes installation in tight spaces easy. Simple to connect using quick connectors on the circuit breakers. Red "ON" indicator lights ensure visibility even in poor lighting conditions.
  
  FEATURES:
  Illuminated circuit breakers that also function as a switch.
• 4 Carling Technologies™ 15A circuit breakers
• ON indicators
• Polycarbonate/ABS panel surface, UV-resistant, fire-retardant, not susceptible to corrosion
• The RAIL with quick connectors eliminates the need for wire harnesses and messy connections
• Two-wire connection to power supply, #10 ring terminals. Terminals are screwed onto busbars to secure connections
• Comes with 15 name tags, easy to replace. More different name tags for different functions are available from Blue Sea Systems' range
• Stainless steel mounting screws #6 x 5/8 included?

Number of circuits: 4

Maximum current 100 A per block | 30 A per circuit

Maximum voltage: 32 VDC

Mounting method: M4 (#8) screw

Terminal tightening torque: 2.71 Nm (24 in-lb)

Terminal block screw tightening torque: 1.69 Nm (15 in-lb)

Terminal block type: #8-32 screws with star washer

Connector pin size: #10-32

Waterproof circuit breaker panel with automatic fuses 15A. Lighting on. Includes 15 different stickers for attachment.

Waterproof (IP67) fully tinned switch panel with circuit breakers and LED lighting. Suitable for both vertical and horizontal installation. Includes 30 different identification stickers that can be glued to the panel.

• Protection class IP67, withstands immersion in water for 30 minutes

• Designed for overhead and open cab applications

• Separate lighting for title slots, switching and dimming options

• Compatible with all Blue Sea Systems digital dimmers

• Also available in 4- and 6-circuit breaker models

• Each panel can be installed in four different positions

• Green LED indicator light makes it easier to read titles in low light. All title slots are illuminated when the panel is powered on, regardless of the position of the individual switches.

Double connection rail for + and – current, with a protective glass made of clear polycarbonate that locks into place. Maximum load 150 A. Both rails have 5 mm terminal bolts and 5 connection screws.

• Contains both negative and positive rail in the same block
  
• Clear polycarbonate lid snaps into place, meets US Coast Guard and ABYC insulation requirements

Automatic charging relay and main circuit breaker package. Complete set for a maximum 65A charger when you want to add a second battery to your boat. The set includes the 6001 MINI ACR charging relay for a 65A charger, and the main circuit breaker 6011 suitable for the set.

Outdoor 12 V panel with a traditional cigarette lighter socket and a USB socket with two inputs. The sockets are protected by a 15A illuminated circuit breaker/thermal fuse. The circuit breaker allows the sockets to be switched off, which prevents hidden consumption of connected devices.

1011 – 12 Volt Surface Mount Connector

1016 – 12/24V USB 2.1A dual charger

Circuit breaker panel with automatic fuses 15A. LED lighting in on mode. Includes 15 different stickers for attachment.

Terminal blocks are used when multiple conductors need to be connected to a single point. The cast stainless steel studs eliminate the need for a retaining nut and allow for a high-torque, reliable connection. The raised rail provides easy access to multiple conductors through a single stud. The UL 94-V0 rated body material is resistant to high temperatures, and recessed mounting holes prevent accidental short circuits on aluminum and steel mounting surfaces.

For connecting two batteries or battery groups. Positions 1-2- OFF - BOTH . E-series main switches are suitable for 350A main switch series for diesel or petrol powered boats with inboard engines. Tinned copper connection bolts ensure maximum conductivity and corrosion protection. The main switch connection bolts are suitable for up to 95mm2 cable, the connection bolts are suitable for M10 cable lugs. 22mm connection bolts allow the installation of several cable lugs on the same connection bolt, the connection bolt made from one piece will never loosen. Suitable as a replacement main switch for most of the main switches from, for example, Perko and Guest. International symbols on the marking labels. The design of the main switch allows for flush, surface and panel mounting.