Mercruiser

Alignment tool MerCruiser Alpha and Bravo

Genuine MerCruiser alignment tool for aligning the engine and drivetrain. The tool is used to check and adjust engine alignment and when replacing the thrust bearing. Proper alignment is essential to ensure long life of the drivetrain, driveshaft and bearings.

The tool should slide easily into the shield, support bearing and engine flywheel coupling. The inner ring of the support bearing can be adjusted slightly with a feeler gauge. If the tool still does not slide easily into place, the engine mounting feet should be adjusted. Lightly greasing the tool will help you see where the alignment is and how to adjust the engine.

When removing the drive, it may be necessary to adjust the engine, especially if the drive is difficult to remove. The engine feet may sag over time, so raising them may make removal easier.

A well-aligned engine prevents damage to the drive shaft and protects the support bearing.

Compatibility

• Fits all MerCruiser Alpha and Bravo drives

Product information

• Product type alignment tool

• Application: engine and drive alignment

• Genuine MerCruiser spare part

Additional information

• OEM number 805475A1

• Previous OEM numbers 57797A3 and 37384

An alignment tool is an essential tool for driveline maintenance and helps ensure proper engine and transmission operation.

Suitable for the following engines:

• 4.3L Carb (serial number 0M615000 and up)
• 4.3L Gen+ (serial number 1G400000-1G416776)
• 4.3L Alpha 4V (serial number 1G417302-1G499999)

Specifications:

• OEM number: 883702K
• Weight: 0.272 kg
• Length: 8.382 cm
• Width: 8.128 cm
• Height: 9.652 cm

Exhaust bellows MerCruiser Alpha One and Bravo

Genuine MerCruiser exhaust bellows for Alpha One and Bravo drives. The exhaust bellows safely directs exhaust gases out through the drive and is an important part of the proper operation of the engine and drive.

The bellows should be replaced regularly according to the engine maintenance instructions. A worn or damaged exhaust bellows can cause water leaks and other serious damage. Delivery includes bellows adhesive for installation.

Compatibility

Fits the following MerCruiser drives and serial numbers

TR and TRS

• TR and TRS 1977–1993 all models

Alpha One

• Alpha One Gen I 1983–1990 all models

• Alpha One Gen II 1991–1995

  • 0D469859 – 0F679999

• Alpha One Gen II 1996–1997

  • 0F680000 – 0K999999

• Alpha One Gen II 1998 and later

  • 0L100040 and newer

Bravo One

• 0B664190 – 0F729999

• 0F730000 – 0M100000

• 0M100001 – 0W249999

• 0W250000 and newer

Bravo Two

• 0B664190 – 0F729999

• 0F730000 – 0M100000

• 0M100001 – 0W249999

• 0W250000 and newer

Bravo Three

• 0B664190 – 0F729999

• 0F730000 – 0M100000

• 0M100001 – 0W249999

• 0W250000 and newer

Bravo X and XR models

• Bravo X Four S 0W250000 and newer

• Bravo X One 0M100001 – 0W249999

• Bravo X Two 0M100001 – 0W249999

• Bravo X Three 0M100001 – 0W249999

• Bravo XR One 0L914990 – 0W239999

• Bravo XR One 0W240000 and newer

• Bravo XR Sport 0M970842 and newer

• Bravo XR Sportmaster 0M052945 – 0M906877

• Bravo XR Sportmaster 0M906878 and newer

• Bravo XR Three 0W240000 and newer

• Bravo XR Three 0W250000 and newer

• Bravo XZ One 0L914990 – 0M999999

Product information

• Product type exhaust pipe bellows

• Includes bubble glue

• Genuine MerCruiser spare part

Additional information

• OEM number 8M0124227

• Previous OEM numbers 18654A1 and 32734A3

Regular inspection and timely replacement of the exhaust bellows help prevent water damage and ensure the safe and long-lasting operation of the drive unit.

Suitable for the following engines:

• 530 D-TA (serial number 0B993002-0D725151)
• 636 D-TA (serial number 0B993002-0D850127)
• D183 Turbo AC (serial number 0B993002-0D725151)
• D219 Turbo AC (serial number 0B993002-0D850127)
• D2.8L/165 D-Tronic (serial number 0K144109-0M999999)
• CMD 2.8 EI/ES 165 (serial number 88005001-88005167)
• D3.0L (serial number 0F306930-0F999999)
• D3.6L (serial number 0F306930 and up)
• D3.6L W (serial number 0K000001 and up)
• D4.2L/200 LD (serial number 0L344381-0M999999)
• D4.2L/220 IDI (serial number 0F450250-0M999999)
• D4.2L/250 D-Tronic (serial number 0K144114-0M999999)
• D4.2L/300 D-Tronic (serial number 0L667439-0M999999)
• CMD 4.2 ES 150 (serial number 88070334-88070344)
• CMD 4.2 MI/MS 200 (serial number 88020001-88020166 and 88020200-88030000)
• CMD 4.2 MI/MS 230 (serial number 88030001-88030344 and 88030400-88040000)
• CMD 4.2 EI/ES 250 (serial number 88040001-88040508 and 88040600 THRU 88050000)
• CMD 4.2 EI/ES 270 (serial number 88060001-88070000)
• CMD 4.2 EI/ES 300 (serial number 88050001-88050643 and 88050800-88060000)
• CMD 4.2 EI/ES 320 (serial number 88070001-88080000)

Specifications:

• OEM number: 19485
• Weight: 0.68 kg
• Length: 19.253 cm
• Width: 11.43 cm
• Height: 11.43 cm

Fuel filter Mercruiser D1.7L

• OEM number: 8M0150911
• Previous OEM number: 882376

Fits engines with serial numbers:

• CMD 1.7 MI 120 I/L4 88109041 & Up
• CMD 1.7 MS 120 I/L4 8810800 & Up
• D1.7L DTI 0M055000 - 0M999999

Dimensions:

• Weight: 0.42kg
• Length: 12.7cm
• Width: 12.7cm
• Height: 6.35cm

Relay Mercury Mercruiser

Relay (also known as solenoid ) used for both the starter and trim pump. Fits many MerCruiser gasoline engines , 2.0 liter diesel engines , and Alpha One and Bravo drives . Also fits some Mercury 250/300XS (DFI Optimax) engines, as well as many older 2-stroke carbureted engines and some EFI models (175-200 hp) .

If the starter or trim pump does not work, this relay could be a possible cause of the problem.

Tip: Check the OEM number of your existing relay before ordering. The number may be on the back of the relay, in which case the relay must be removed for inspection.

Note:

• Spare part 82151 is available as an alternative

• Mercury also has a universal relay, OEM 82152

OEM: 8M0185622
Previous OEM numbers: 96158T, 96158B, 96158, 846070, 94318

Fits the following outboard motors (according to serial number)

35 HP

• 35 (2 cyl.) > 209608 & up

• 35 (2 cyl.) > 6445653 – OB110788

• 35 (2 cyl.) > 9384476 & up

• 35 (2 cyl.) > 9466647 & up

• 35 (2 cyl.) > B110789 & up

40 HP

• 40 / 400 / 402 (2 cyl.) > 5556230 & up

• 40 / 400 / 402 (2 cyl.) > 7144763 & up

• 40 / 400 / 402 (2 cyl.) > 8064750 & up

• 40 / 400 / 402 (2 cyl.) > 9251456 & up

45 HP

• 45 / 450 (4 cyl.) > 5531630 – OB110788

• 45 / 450 (4 cyl.) > 7143688 – OA719280

• 45 / 450 (4 cyl.) > 8063985 & up

• 45 / 450 (4 cyl.) > 9248006 – 9466691

• 45 / 450 (4 cyl.) > 9466692 & up

50 HP

• 50 / 500 (4 cyl.) > 5531630 & up

• 50 / 500 (4 cyl.) > 7143688 & up

• 50 / 500 (4 cylinders) > 8063985 & up

• 50 / 500 (4 cylinders) > 9248006 & up

• 50 (3 cyl.) > 6428681 – OB122929

• 50 (3 cyl.) > 7208333 – OA721307

• 50 (3 syl.) > 9385911 – 9469199

• 50 (3 stitches) > 9469200 – 9683054

• 50 (3 cyl.) > 0A721308 & up

• 50 (3 cyl.) > 0B122930 – OD000749

(the list continues with the same structure for all declared power classes: 60–300 HP)

Fits the following inboard engines (Inboard)

2.0L Diesel (EI / ES / CMD QSD)

• 2.0L NOT 115 > 70294910 – 70377490

• 2.0L NOT 130 > 70000000 – 70002129

• 2.0L NOT 150 > 70015460 – 70017409

• 2.0L NOT 170 > 70024870 – 70026629

• 2.0L ES 130 > 70002130 – 70015639

• 2.0L ES 150 > 70017410 – 70024869

• 2.0L ES 170 > 70026630 – 70105129

CMD QSD 2.0

• NO 115 > 88200000 – 88200999

• NOT 130 > 88205000 – 88205999

• NOT 150 > 88220299 – 88220999

• NOT 170 > 88230000 – 88230999

• ES 130 > 88206399 – 88219999

• ES 150 > 88221799 – 88229999

• ES 170 > 88231000 – 88239999

Fits the following towbars (according to serial number)

Alpha One

• Alpha One Gen I > 1983–1990

• Alpha One Gen II > 1991–1995 > 0D469859 – 0F679999

• Alpha One Gen II > 1996–1997 > 0F680000 – OK999999

• Alpha One Gen II > 1998 & up > OL100040 & up

Bravo One / Two / Three

• Bravo One > 0B664190 – 0F729999

• Bravo One > 0F730000 – 0M100000

• Bravo One > 0M100001 – 0W249999

• Bravo One > 0W250000 & up

• Bravo Two > similar series

• Bravo Three > similar series

Bravo XR / X / XZ

• Bravo XR One > 0L914990 – 0W239999

• Bravo XR One > 0W240000 & up

• Bravo XR Sport > 0M970842 & up

• Bravo X One / Two / Three > 0W250000 & up

Universal relay Mercury and MerCruiser

Universal relay for Mercury and MerCruiser engines. The relay can be used as both a starter and trim pump relay, and is also called a solenoid. The relay was originally used in older MerCruiser trim pumps from 1974-1976, but is now widely used as a universal relay in both Mercury MerCruiser engines and many other sterndrive and inboard engines.

If the starter motor or trim pump is not working properly, this relay could be a possible cause of the problem.

Compatibility

• Mercury and MerCruiser sterndrives and inboard engines

• Suitable as starter and trim pump relay

• Universal solution for multiple engines

Product information

• Product type relay solenoid

• Application starter and trim pump

• Distance between mounting holes approx. 55 mm

• Width approximately 7 mm

• Original equivalent spare part

Additional information

• OEM number 25661T1

• Previous OEM numbers 256611 and 25661

In the event of electrical system malfunctions, it is worth checking the condition of the relay, as a faulty relay can prevent starting or the trim system from functioning.

Seawater hose for MerCruiser Alpha One drives

Seawater hose for MerCruiser Alpha One drives. Genuine MerCruiser spare part that ensures reliable operation of the cooling system and prevents water from entering the wrong places.

It is important to check the condition of the hose regularly, as a damaged or frayed hose can cause water leaks and serious damage to the engine or drivetrain. If the OEM number is not known, it is a good idea to measure the diameter of the hose before ordering.

Compatibility

Fits the following MerCruiser drives

• Alpha One Gen I 1983–1990

• Alpha One Gen II 1991–1995

  • Serial numbers 0D469859 – 0F679999

• Alpha One Gen II 1996–1997

  • Serial numbers 0F680000 – 0K999999

• Alpha One Gen II 1998 and later

  • Serial numbers 0L100040 and later

Product information

• Product type seawater hose

• Application: seawater suction

• Inner diameter 19 mm

• Genuine MerCruiser spare part

Additional information

• OEM number 8M0215001

• Previous OEM number 8M0109048

Regular hose inspection and replacement, if necessary, helps prevent water damage and ensures safe operation of the engine and drivetrain.

Thrust bearing MerCruiser Alpha One Gen II and Bravo newer models

Genuine MerCruiser thrust bearing for newer Alpha One Gen II and Bravo I, II and III drives. The thrust bearing supports the drive shaft and is a key component in the smooth and quiet operation of the drivetrain. A worn or damaged thrust bearing often causes noise and can lead to more serious damage if not replaced in a timely manner.

The bearing is supplied with a grease nipple plug, as this model has permanent grease. An alignment tool is recommended for installation to ensure the new thrust bearing is correctly aligned.

Compatibility

Fits the following MerCruiser drives

• Alpha One Gen II

  • Model years 1998 and newer

  • Serial numbers 0L100040 and later

• Bravo One

  • Serial numbers 0F730000 and later

• Bravo Two

  • Serial numbers 0F730000 and later

• Bravo Three

  • Serial numbers 0F730000 and later

If the drive unit is not listed above, see alternative part number 82133.

Product information

• Product type support bearing

• Application: drive shaft support

• Permanently lubricated structure

• Includes a plug for the grease nipple

• Genuine MerCruiser spare part

Additional information

• OEM number 879194A01

• Previous OEM numbers 862540A3 and 862540T1

Correct installation of the thrust bearing and engine alignment are crucial to ensuring the longevity and trouble-free operation of the drive unit.

Service kit MerCruiser 4.3 TKS carburetor engines 1993–

100-hour service kit for MerCruiser 4.3 TKS carburetor engines from 1993 onwards. The kit is intended for engines that do not have a separate oil filter housing , i.e. the oil filter is located directly in the engine block.

The maintenance kit contains the most important parts for regular scheduled maintenance and helps ensure reliable engine operation and a long service life.

Maintenance kit contents

• Oil filter

• Fuel filter

• Drivetrain seals

Compatibility

Fits the following MerCruiser engines and serial numbers

4.3L CARB Alpha and Bravo

• 0W300013 – 0W309999

• 0W310000 – 0W649999

• 0W650000 – 1A063239

• 1A063240 and newer

• 0M615000 – 0W300012

Product information

• Product type 100 hour service kit

• Engine type 4.3 TKS carburetor engine

• Oil filter in the block

• Genuine MerCruiser spare part

Additional information

• OEM number 8M0147050

The service kit offers an easy and cost-effective solution for regular maintenance of your MerCruiser 4.3 TKS engine and helps keep your engine running reliably throughout the boating season.

Disassembly tool Mercruiser Alpha Bravo

Disassembly tool used to remove drive mounting bolts . Genuine MerCruiser replacement part. This special tool fits most MerCruiser drives and is essential when removing the drive .

OEM: 78310

Fits the following towbars (according to serial number)

Alpha One

• Alpha One (Gen I) > 1983–1990 > all

• Alpha One (Gen II) > 1991–1995 > 0D469859 – 0F679999

• Alpha One (Gen II) > 1996–1997 > 0F680000 – OK999999

• Alpha One (Gen II) > 1998 & up > 0L100040 & up

Bravo One

• Bravo One > 0B664190 – 0F729999

• Bravo One > 0F730000 – 0M100000

• Bravo One > 0M100001 – 0W249999

• Bravo One > 0W250000 & up

Bravo Two

• Bravo Two > 0B664190 – 0F729999

• Bravo Two > 0F730000 – 0M100000

• Bravo Two > 0M100001 – 0W249999

• Bravo Two > 0W250000 & up

Bravo Three

• Bravo Three > 0B664190 – 0F729999

• Bravo Three > 0F730000 – 0M100000

• Bravo Three > 0M100001 – 0W249999

• Bravo Three > 0W250000 & up

Bravo X-series

• Bravo X Four S > 0W250000 & up

• Bravo X One > 0M100001 – 0W249999

• Bravo X Two > 0M100001 – 0W249999

• Bravo X Three > 0M100001 – 0W249999

Bravo XR / XZ

• Bravo XR One > 0L914990 – 0W239999

• Bravo XR One > 0W240000 & up

• Bravo XR Sport > 0M970842 & up

• Bravo XR Sportmaster > 0M052945 – 0M906877

• Bravo XR Sportmaster > 0M906878 & up

• Bravo XR Three > 0W240000 & up

• Bravo XR Three > 0W250000 & up

• Bravo XZ One > 0L914990 – 0M999999

Aluminum Anode Kit for MerCruiser Alpha One Drive

Complete aluminum anode kit for MerCruiser Alpha One drives. The kit is intended for first generation Alpha One drives manufactured between 1983 and 1990. The kit includes all the necessary anodes for effective corrosion protection of the drive.

Sacrificial anodes are made of a base metal, which means they corrode first and protect the drivetrain structures. The general recommendation is to replace the anode when about half of the material has worn away.

Compatibility

Fits the following MerCruiser drives

• Alpha One

• Serial numbers 6216687 – 0F386995

Years of manufacture 1983–1990

Product information

• Material aluminum

• Complete anode kit for the traction device

• Designed for marine use

Additional information

• OEM number 888756K02

• Previous OEM numbers 888756Q04, 888756Q02 and 888756A2

Regular inspection of anodes and timely replacement will extend the life of the drive unit and protect valuable parts of the boat from corrosion.

Seawater hose kit for MerCruiser Bravo drives

Seawater hose kit for MerCruiser Bravo drives. A genuine MerCruiser replacement part designed to ensure reliable and leak-tight operation of the cooling system.

The hose kit fits earlier models of Bravo I, II and III towbars. Some later model years may have an alternative hose solution, so if you are unsure of the OEM number, it is recommended to compare the part to the product image. The towbar serial number alone is not always sufficient to identify the correct hose.

The condition of seawater hoses should always be checked during maintenance, as a damaged or worn hose can cause water to enter the drive unit or engine compartment.

Compatibility

Fits the following MerCruiser drives

• Bravo I

• Bravo II

• Bravo III

Especially early models. Newer models may have a different hose design.

Product information

• Product type seawater hose kit

• Application: seawater suction

• Genuine MerCruiser spare part

Additional information

• OEM number 8M0090859

Regular inspection of seawater hoses and replacement if necessary prevents water damage and ensures proper operation of the cooling system.

Service kit MerCruiser Bravo III 2003–

100-hour service kit for MerCruiser Bravo III drives, model years 2003 and later. The kit contains essential parts for scheduled drive maintenance and helps maintain effective corrosion protection and tight, reliable operation.

Regular maintenance according to the manufacturer's instructions will extend the life of the drive unit and reduce the risk of damage during the boating season.

Maintenance kit contents

• 1 set of anodes

• 2 pcs oil plug seals

• Installation kit, includes O-rings and seal

Compatibility

Fits the following MerCruiser drives

• Bravo Three

  • Serial numbers 0M100001 – 0W249999

  • Serial numbers 0W250000 and later

• Bravo X Three

  • Serial numbers 0W250000 and later

Product information

• Product type 100 hour service kit

• Application: towing device

• Genuine MerCruiser spare part

Additional information

• OEM number 8M0147058

The maintenance kit is an easy and cost-effective solution for regular maintenance of the Bravo III drive unit and helps keep the drive unit reliable and well protected throughout the entire operating season.

Cardan bellows MerCruiser Alpha One Gen I

Genuine MerCruiser drive shaft bellows for Alpha One Gen I drives. The drive shaft bellows protects the drive joint and drive shaft from water and debris entering the drive. The condition of the bellows is very important for the operation and service life of the drive.

The bellows must be completely sealed, and it is recommended to replace it regularly according to the engine maintenance schedule. It is recommended to use bellows glue, sold separately, during installation.

Compatibility

Fits the following MerCruiser drives and engines

• Alpha One Gen I 1983–1990

• TR and TRS 1977–1993

• 120 and 140 1978–1982

• 165 1978–1981

• 898 1978–1982

• 260 1978–1982

• 470 1978–1982

  • Serial numbers 4893835 – 6225576

• 485 1980–1982

• 228 1978–1982

Product information

• Product type cardan bellows

• Application: drive shaft and drive joint

• Genuine MerCruiser spare part

• OEM number 60932A4

• Previous OEM number 60932A1

Regular inspection of the bellows and timely replacement prevent water from entering the drive unit and help avoid costly repair damage.

Service kit MerCruiser Alpha One Gen II 1991–

100-hour service kit for MerCruiser Alpha One Gen II drives, model years 1991 and later. The kit contains essential parts for scheduled drive maintenance and helps ensure good corrosion protection and a leak-proof, reliable structure.

Regular maintenance according to the manufacturer's instructions will extend the life of your drive unit and prevent costly damage during the boating season.

Maintenance kit contents

• 1 set of anodes

• 2 pcs oil plug seals

• Installation kit, includes seals and O-rings

Compatibility

Fits the following MerCruiser drives

• Alpha One Gen II 1991–1995

  • Serial numbers 0D469859 – 0F679999

• Alpha One Gen II 1996–1997

  • Serial numbers 0F680000 – 0K999999

• Alpha One Gen II 1998 and later

  • Serial numbers 0L100040 and later

Product information

• Product type 100 hour service kit

• Application: towing device

• Genuine MerCruiser spare part

Additional information

• OEM number 8M0147055

The maintenance kit is an easy and cost-effective solution for regular maintenance of your Alpha One Gen II drive unit and helps keep the drive unit reliable and well-protected throughout the entire operating season.

Thermostat kit Mercruiser GM

Thermostat kit to fit GM based MerCruiser engines from 1987 onwards . The thermostat is designed for use in cooling systems with constant circulation and has an opening temperature of 160°F (71°C) . The kit includes all necessary gaskets for thermostat replacement.

The thermostat is an important part of the engine's cooling system. It regulates the engine's operating temperature . A faulty thermostat can cause the engine to overcool or overheat . In the worst case, the engine can boil, but running too cold is also not good, as it increases wear and fuel consumption .

Make sure the thermostat opens and closes at the correct temperature. You can test your current thermostat by heating it in water and checking to see if it opens at the correct temperature. If you are unsure about the thermostat's operation, it is a good idea to replace it .

OEM: 807252T5
Previous OEM numbers: 807252Q5, 8M0109441, 807252T8

Fits the following engines (according to serial number)

3.0L

• 3.0L GM 181 I/L4 > 1A002000 – 1A020543

• 3.0L GM 181 I/L4 > 1A020544 & up

• 3.0L MPI EC > 1A072812 & up

• 3.0L Crate Engine > 1G800000 – 1G899999

4.3L

• 4.3L CARB ALPHA/BRAVO > 0M615000 – 0W300012

• 4.3L CARB ALPHA/BRAVO > 0W300013 – 0W309999

• 4.3L CARB ALPHA/BRAVO > 0W310000 – 0W649999

• 4.3L CARB ALPHA/BRAVO > 0W650000 – 1A063239

• 4.3L CARB ALPHA/BRAVO > 1A063240 & up

• 4.3L MPI ALPHA/BRAVO > 0M615000 – 0W309999

• 4.3L MPI ALPHA/BRAVO > 0W310000 – 0W649999

• 4.3L MPI ALPHA/BRAVO > 0W650000 – 0W658582

• 4.3L MPI ALPHA/BRAVO > 0W658583 – 0W658583

• 4.3L MPI ALPHA/BRAVO > 0W658584 – 1A030367

• 4.3L MPI ALPHA/BRAVO > 1A030368 – 1A030369

• 4.3L MPI ALPHA/BRAVO > 1A030370 – 1A063239

• 4.3L MPI ALPHA/BRAVO > 1A063240 & up

• 4.3L Alpha 4V EST > 1G417302 – 1G499999

5.0L

• 5.0L MPI ALPHA/BRAVO EC > 1A300000 – 1A611927

• 5.0L MPI ALPHA/BRAVO > 1A611928 – 1A623184

• 5.0L MPI ALPHA/BRAVO EC > 1A611928 – 1A623184

• 5.0L MPI ALPHA/BRAVO > 1A623185 & up

• 5.0L MPI ALPHA/BRAVO EC > 1A623185 & up

350 CID (5.7L)

• 350 MPI ALPHA > 1G400000 – 1G499999

• 350 MPI BRAVO > 1G400000 – 1G499999

• 350 MPI Alpha/Bravo > 1G700000 – 1G799999

• 350 MAG MPI HORIZON ALPHA/BRAVO EC > 1A300000 – 1A611927

• 350 MAG MPI ALPHA/BRAVO EC > 1A300000 – 1A611927

• 350 MAG MPI ALPHA/BRAVO > 1A611928 – 1A623184

• 350 MAG MPI HORIZON ALPHA/BRAVO EC > 1A611928 – 1A623184

• 350 MAG MPI ALPHA/BRAVO EC > 1A611928 – 1A623184

• 350 MAG MPI ALPHA/BRAVO > 1A623185 & up

• 350 MAG MPI HORIZON ALPHA/BRAVO EC > 1A623185 & up

• 350 MAG MPI ALPHA/BRAVO EC > 1A623185 & up

377 CID (6.2L)

• 377 MAG MPI BRAVO EC > 1A343300 – 1A611927

• 377 MAG MPI BRAVO > 1A611928 – 1A623184

• 377 MAG MPI BRAVO EC > 1A611928 – 1A623184

• 377 MAG MPI BRAVO > 1A623185 & up

• 377 MAG MPI BRAVO EC > 1A623185 & up

383 CID (6.3L)

• 383 MAG STROKER BRAVO > 1G400000 – 1G499999

Mercury Mercruiser oil filter. Replace the oil filter according to the recommendations for your engine. This genuine spare part fits D7.3L D-tronic engines with serial numbers: 0L050050-0L391832.

Information:

• OEM number: 862889
• Weight: 1.0 kg
• Length: 26.92 cm
• Width: 14.22 cm
• Height: 13.46 cm

Aluminum Anode Kit for MerCruiser Alpha One Gen II Drive

Complete aluminum anode kit for MerCruiser Alpha One Gen II drives. The kit is intended for second generation Alpha One drives manufactured since 1991. The kit includes all the necessary anodes for effective corrosion protection of the drive.

Sacrificial anodes are made of a base metal, which means they corrode first and protect the drivetrain structures. The general recommendation is to replace the anode when about half of the material has worn away.

Compatibility

Fits the following MerCruiser drives and serial numbers

• Alpha One Gen II 1991–1995 0D469859 – 0F679999

• Alpha One Gen II 1996–1997 0F680000 – 0K999999

• Alpha One Gen II 1998 and later 0L100040 and later

Product information

• Material aluminum

• Complete anode kit for the traction device

• Designed for marine use

Additional information

• OEM number 888756K01

• Previous OEM numbers 888756Q03 and 888756Q01

Regular inspection of anodes and timely replacement will extend the life of the drive unit and protect valuable parts of the boat from corrosion.

Thrust bearing MerCruiser Alpha One and Bravo older models

Genuine MerCruiser thrust bearing for older Alpha One and Bravo drives. The thrust bearing supports the drive shaft and is an important part of the smooth and quiet operation of the drivetrain. A worn or damaged thrust bearing often causes excessive noise and can lead to more serious damage if not replaced in a timely manner.

The bearing is supplied with a grease nipple plug as this model has permanent grease. It is recommended to use an alignment tool during installation to ensure correct alignment of the support bearing.

Compatibility

Fits the following MerCruiser drives

• Alpha One 1983–1990 all models

• Alpha One Gen II until 1997

  • Serial numbers up to 0K999999

• Bravo One

  • Serial numbers up to 0F729999

• Bravo Two

  • Serial numbers up to 0F729999

• Bravo Three

  • Serial numbers up to 0F729999

If the drive unit is not listed above, see alternative part number 82134.

Product information

• Product type support bearing

• Application: drive shaft support

• Permanently lubricated structure

• Includes a plug for the grease nipple

• Genuine MerCruiser spare part

Additional information

• OEM number 879194A02

• Previous OEM numbers 60794A4 and 60794A2

A properly installed and aligned thrust bearing ensures a long life for the drivetrain, reduces noise and protects other parts of the drivetrain from wear.