Tyresöbocken

Very durable Tyresöbocken boat stand with steel beam. Powder-coated steel, and the side supports have telescopic legs and articulated frame plates for fine adjustment. In addition, a center support for a larger load. The maximum weight of one stand is 5000kg, which means that the maximum weight of the boat can be a maximum of 10000kg with a 50/50 weight distribution.

Maximum boat weight:

• With a 30/70% weight distribution, the maximum weight is 7000kg.
• With a 50/50% weight distribution, the maximum weight is 10,000kg.

Very durable Tyresöbocken boat stand with steel beam. Powder-coated steel, and the side supports have telescopic legs and articulated frame plates for fine adjustment. In addition, a center support for a larger load. The maximum weight of one stand is 5000kg, which means that the maximum weight of the boat can be a maximum of 10000kg with a 50/50 weight distribution.

Maximum boat weight:

• With a 30/70% weight distribution, the maximum weight is 7000kg.
• With a 50/50% weight distribution, the maximum weight is 10,000kg.

Vertical boat support made of hot-dip galvanized steel. Adjustable height 60-90cm. Quick height adjustment with trapezoidal thread and wing nut. Large, rectangular rubber-coated frame support made of painted marine plywood. The support adapts to the bottom of the boat, but if you have a boat with a deep V-bottom you can use two vertical motorboat support legs at the stern and two tilted sailboat support legs at the bow. The supports are stackable to minimize storage space.

• The recommendation is two supports per 8-10 feet of length.
• The weight and support of the boat should be on the keel strip
• Always use chains between supports

Number of supports: recommendation according to boat length below

• >30 feet 4 pcs
  
• 30-45 feet 6 pieces
• 45< feet 8 pieces or more

Very durable Tyresöbocken boat stand with steel beam. Side supports made of powder-coated steel with telescopic legs and articulated frame plates for fine adjustment. The maximum weight of one stand is 1500kg, which means that the maximum weight of the boat can be up to 3000kg with a 50/50 weight distribution.

Maximum boat weight:

• With a 30/70% weight distribution, the maximum weight is 2000kg.
• With a 50/50% weight distribution, the maximum weight is 3000kg

Vertical boat support made of hot-dip galvanized steel. Adjustable height 75-105cm. Quick height adjustment with trapezoidal thread and wing nut. Large, rectangular rubber-coated frame support made of painted marine plywood. The support adapts to the bottom of the boat, but if you have a boat with a deep V-bottom you can use two vertical motorboat support legs at the stern and two tilted sailboat support legs at the bow. The supports are stackable to minimize storage space.

• The recommendation is two supports per 8-10 feet of length.
• The weight and support of the boat should be on the keel strip
• Always use chains between supports

Number of supports: recommendation according to boat length below

• >30 feet 4 pcs
  
• 30-45 feet 6 pieces
• 45< feet 8 pieces or more

Tilted sailboat support. Adjustable height 110-155cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.

Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.

Number of supports: recommendation according to boat length below

• >25 feet 4 pcs
  
• 25-30 feet 6 pieces
• 30-40 feet 6-8 pieces
• 40-55 feet 8-10 pieces or more

Tilted sailboat support. Adjustable height 190-235cm. Foldable. Powder coated steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.

Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.

Number of supports: recommendation according to boat length below

• >25 feet 4 pcs
  
• 25-30 feet 6 pieces
• 30-40 feet 6-8 pieces
• 40-55 feet 8-10 pieces or more

Vertical boat support made of hot-dip galvanized steel. Adjustable height 90-120cm. Quick height adjustment with trapezoidal thread and wing nut. Large, rectangular rubber-coated frame support made of painted marine plywood. The support adapts to the bottom of the boat, but if you have a boat with a deep V-bottom you can use two vertical motorboat support legs at the stern and two tilted sailboat support legs at the bow. The supports are stackable to minimize storage space.

• The recommendation is two supports per 8-10 feet of length.
• The weight and support of the boat should be on the keel strip
• Always use chains between supports

Number of supports: recommendation according to boat length below

• >30 feet 4 pcs
  
• 30-45 feet 6 pieces
• 45< feet 8 pieces or more

Tilted sailboat support. Adjustable height 130-175cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.

Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.

Number of supports: recommendation according to boat length below

• >25 feet 4 pcs
  
• 25-30 feet 6 pieces
• 30-40 feet 6-8 pieces
• 40-55 feet 8-10 pieces or more

Tilted sailboat support. Adjustable height 170-215cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.

Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.

Number of supports: recommendation according to boat length below

• >25 feet 4 pcs
  
• 25-30 feet 6 pieces
• 30-40 feet 6-8 pieces
• 40-55 feet 8-10 pieces or more

Very sturdy outboard motor stand. Compatible with motors weighing up to 150kg. Durable welded square profile.

An optional compatible cart for moving is: Tyresö motorized trestle cart 8896.

"Hot-dip galvanized steel top plate with stainless bolt and nut for sailboat and motorboat supports. Upholstered with hull protection made of EPDM rubber.

Suitable for MBS and SBS supports, but also for other similar support models on the market.

It is recommended to replace it if, for example, your old wooden top plate is broken.

Dimensions: 255x255 mm.

Frame protector for Tyresöbocken 1550kg boat stand. Size 16x16cm.

Tilted sailboat support. Adjustable height 150-195cm. Foldable. Galvanized steel. Flexible, rubber-coated ball base. Chains should always be used between the support legs.

Choosing the right support leg height: usually the easiest way to choose the right support is to calculate the boat draft + keel support height -25cm. Another good way is to choose the support according to the boat draft, then the draft should be in the middle of the support's adjustment range. So if the draft is 180cm, a 170-215 high support leg could be a good choice. Tyresöstötta's support legs have 45cm of adjustment range, leaving 15cm of the pipe end inside the support.

Number of supports: recommendation according to boat length below

• >25 feet 4 pcs
  
• 25-30 feet 6 pieces
• 30-40 feet 6-8 pieces
• 40-55 feet 8-10 pieces or more

Very sturdy outboard motor stand. Compatible with engines weighing up to 225kg. Durable welded square profile.

A compatible cart for moving is available as an accessory: Tyresö motorized trestle cart 8899.

"Hot-dip galvanized steel top plate with stainless bolt and nut for motorboat supports. Covered with a hull protector made of EPDM rubber. Due to its narrow design, the top plate fits better against the hull compared to a traditional square top plate.

Suitable for MBS supports, but also for other similar support models on the market.

It is recommended to replace it if, for example, your old wooden top plate is broken.

Dimensions: 310x160 mm.

Frame protector for Tyresöbocken Type 1 boat stands and sailboats. Size: 21x21cm.

A wheeled cart that allows you to move a Tyresö outboard motor stand 225kg. Suitable for outboard motors up to 225kg. The welded square profile sinks into the legs of the outboard motor stand, making it easy to move.

Very sturdy outboard trailer. Compatible with engines weighing up to 225kg. Durable tires, axles and welded steel square profile frame. The 225kg outboard trailer has larger tires and a more durable axle than the 150kg model.