Hydraulic hoses
Hydraulic hoses and accessories for hydraulic steering.Product groups
Hydraulic hoses group products
/glydus-hydraulkoppling-dual-06aa40418cb55a.webp)
new
The Glydus 90° hydraulic fitting is an elbow fitting for hydraulic steering systems. It is suitable for installations where the hydraulic hose needs to be connected at a 90-degree angle, for example due to limited installation space.
The fitting is suitable for connecting an autopilot as well as for dual-station steering systems using a dual pump. The angled design makes it easier to install hydraulic hoses neatly and efficiently, especially in confined spaces.
Features
- 90-degree elbow fitting for hydraulic steering
- Designed for dual-pump installations
- Suitable for connecting an autopilot
- Suitable for dual-station steering systems
- Makes hydraulic hose installation easier in confined spaces
- Enables neat and space-saving hose routing
- For Glydus hydraulic steering systems
- Dual fitting for hydraulic steering
- Connects two lines at one point
- Fits Glydus/Multisteer systems
- Tight, reliable connection
/302669e23ff7892c0.jpg)
/glydus-hydraulkoppling-avluft-06aa3f26868779.webp)
new
Glydus's T-union fitting with a bleed valve is designed to be fitted to the steering cylinder in a hydraulic steering system. The fitting is used to connect hydraulic hoses while also allowing the system to be bled at the same time — air trapped in a hydraulic steering circuit causes a soft, imprecise feel at the wheel, so a working bleed valve makes filling the system after installation or service much easier.
Built for marine hydraulic installations where correct pressure and a tight seal are critical. Fits Glydus/Multisteer systems with 3/8-24 UNF thread.
Built for marine hydraulic installations where correct pressure and a tight seal are critical. Fits Glydus/Multisteer systems with 3/8-24 UNF thread.
- T-union fitting with built-in bleed valve
- Fits onto the steering cylinder
- Makes filling and bleeding the system easier
- 3/8-24 UNF thread
/glydusmultisteer-slangkopplin-06aa3f30ba0767.webp)
new
Glydus's straight hose nipple is designed to connect hydraulic hose in a Glydus hydraulic steering system. The straight design suits points where a direct hose run is needed between steering system components, without an angled fitting getting in the way. Built for marine installations where a secure, tight hose connection matters. Fits 5/16'' hydraulic hose in Glydus/Multisteer systems.
- Straight hose nipple for hydraulic steering
- Fitted for Glydus systems
- For 5/16'' hose
/glydusmultisteer-slangkit-3m-06aa3f23521be7.webp)
new
Glydus's hydraulic hose kit includes 3 metres of hose with factory-crimped HC-R1 hydraulic fittings already attached, so there's no need to crimp hoses on-site — faster installation and lower risk of leaks. The hose is made from thermoplastic elastomer with synthetic fibre reinforcement and a durable black polyurethane cover. It's rated for continuous use from -40°C to +100°C, giving a safe, flexible, long-lasting solution for marine hydraulic steering.
The 3m length suits shorter runs well, for example between the helm and the engine on a smaller boat, or as part of a larger Glydus/Multisteer hydraulic steering installation or service job.
The 3m length suits shorter runs well, for example between the helm and the engine on a smaller boat, or as part of a larger Glydus/Multisteer hydraulic steering installation or service job.
- Ready-made 3m hose kit, HC-R1 fittings fitted
- Fibre-reinforced, rated -40 to +100°C
- Black polyurethane cover
- Faster install, no on-site crimping needed
/glydusmultisteer-slangkit-6m-06aa3f24ebc929.webp)
new
Glydus's hydraulic hose kit includes 6 metres of hose with factory-crimped HC-R1 hydraulic fittings already attached, so there's no need to crimp hoses on-site — faster installation and lower risk of leaks. The hose is made from thermoplastic elastomer with synthetic fibre reinforcement and a durable black polyurethane cover. It's rated for continuous use from -40°C to +100°C, giving a safe, flexible, long-lasting solution for marine hydraulic steering.
The 6m length suits longer runs, for example on a bigger boat between the helm and the outboard/engine, or as part of a Glydus/Multisteer hydraulic steering installation or service job.
The 6m length suits longer runs, for example on a bigger boat between the helm and the outboard/engine, or as part of a Glydus/Multisteer hydraulic steering installation or service job.
- Ready-made 6m hose kit, HC-R1 fittings fitted
- Fibre-reinforced, rated -40 to +100°C
- Black polyurethane cover
- Faster install, no on-site crimping needed
/glydusmultisteer-t-kors-06aa3f27d79244.webp)
new
The Glydus TF1 T-fitting is designed for use in boat hydraulic steering systems. It's used to branch hydraulic hoses during steering system installation or modification — for example, when a feed from one line needs to reach two points, such as the steering cylinder and an autopilot pump. Built to marine-grade standards with an emphasis on reliability and a tight seal. Fits applications using 9/16 UNEF thread.
- T-fitting for branching hydraulic hoses
- For hydraulic steering systems
- 9/16 UNEF thread
/seafirst-hosekit-38-6m-067875be0c7133.jpg)
OUTLET
Hydraulic steering hose, 6 meters long, with 3/8" connectors.
- Length: 6m
- Connectors: 3/8"
/31946aad4806630fc.jpg)
OUTLET
Hydraulic steering hose, 6m long and with 3/8" connectors.
- Length: 6m
- Connectors: 3/8"
/ultraflex_gotech_hydrauliletku_14-0678a64089cee1.picture_manager_678a630e83b6c.jpg)
Suitable for 'Bullhorn' steering and side and hydraulic steering for outboard motors. Hose length: 2x distance between steering pump and hydraulic cylinder. When installing an autopilot or additional cockpit, hose is required: 1x distance between steering rods and hydraulic cylinder + 2 pcs. connectors.
- Gotechille
- 50m/roll
- Ultraflex
/5206ab26bdad219a.jpg)
/ultraflex_gotech_liitin_14_letkulle-0678a64089f48d.picture_manager_678a630e86b32.jpg)
4 connectors per control system.
93089: Connector 3/8" thread for 1/4'' high pressure hose.
93089: Connector 3/8" thread for 1/4'' high pressure hose.
- Gotech connector for 1/4 hose
- 2pcs
- Ultraflex
/ultraflex_hydrauliletku_1m_pari-0678a6409510a6.picture_manager_678a630ee674b.jpg)
Fixed length high pressure hose with crimped nipples.
- High-pressure hose
- Fixed lengths
- 2 pieces in the package
- Length: 1m
/hydrauliletku-067875b9f6a019.jpg)
Campaign
This hose is specifically made for hydraulic steering. A ready-to-install, flexible hydraulic hose for stern, mid- and sterndrive engines.
- fits directly into the hydraulic pump
- hydraulic cylinder 3/8 inch thread
- sold in pairs / price per pair
- Flexi Hose Kit
- Length 3-9m
/ultraflex_hydrauliletku_38-0678a642172a26.picture_manager_678a6324329db.jpg)
Hydraulic oil hose for Ultraflex hydraulic controls. 3/8 meter length.
- For Ultraflex hydraulic controls
- 3/8"
- Metric goods
/ultraflex_hydrauliletku_516-0678a6408b2ac2.picture_manager_678a630eade65.jpg)
Suitable for "Bullhorn" steering and side-mounted hydraulic steering for outboard motors.
Hose length: 2x distance between steering pump and hydraulic cylinder.
When installing an autopilot or additional steering position, a hose is required: 1x distance between the steering pump and the hydraulic cylinder + 2 pcs of connectors.
Hose length: 2x distance between steering pump and hydraulic cylinder.
When installing an autopilot or additional steering position, a hose is required: 1x distance between the steering pump and the hydraulic cylinder + 2 pcs of connectors.
• New 2008
• 150m/roll
• Ultraflex
• 150m/roll
• Ultraflex
/ultraflex_hydrauliletkusarja_38_kaksoisasennukseen-0678a6408a6402.picture_manager_678a630e96823.jpg)
Hose kit for dual installation. Also used when connecting an autopilot with a hydraulic pump to a hydraulic steering system. Supplied with connectors and 8 meters of 3/8" nylon tubing.
- Hydraulic hose kit for double point installation
- Supplied with connectors and 8 meters of 3/8" nylon tubing.
/ultraflex_hydrauliletkusarja_516_kaksoisasennukseen-0678a640947d48.picture_manager_678a630ed2163.jpg)
Complete package for connecting a second steering pump or autopilot to an existing hydraulic system with 5/16 hydraulic hoses.
Contain:
2 pcs 93088 T-pieces
4 pcs 93084 straight connectors
8 pcs 93079 hose connectors suitable for 5/16 hydraulic hoses
2 pcs 93097 bypass fittings to be attached to both steering pumps
1 pc. filling connector, which is not vented, and which replaces the existing connector on the lower steering pump
2 pcs of hoses 5/16, each 10 m long
Contain:
2 pcs 93088 T-pieces
4 pcs 93084 straight connectors
8 pcs 93079 hose connectors suitable for 5/16 hydraulic hoses
2 pcs 93097 bypass fittings to be attached to both steering pumps
1 pc. filling connector, which is not vented, and which replaces the existing connector on the lower steering pump
2 pcs of hoses 5/16, each 10 m long
• Complete set
• 5/16
• Ultraflex
• 5/16
• Ultraflex
/ultraflex-kaasuvaijerin-liitin-067875c2936120.)
Suitable for cables C2, C8, Czero and 33C
- Diameter: 7mm
- Shaft length: 10mm
/ultraflex-liitin-38-putkelle-90-kulma-067875c1c1e452.jpg)
Connector elbow 1/4 NPT for 3/8” OD pipe.
- 90° angle
- For 3/8" OD pipe
/ultraflex-liitin-38-putkelle-t-kulma-067875c1189557.jpg)
Connector for 3/8” OD pipe.
- T-angle
/ultraflex_liitin_suora-0678a6408a1823.picture_manager_678a630e88104.jpg)
Direct hydraulic connector for Ultraflex hydraulic steering systems.
- For Ultraflex hydraulic controls
- Straight hydraulic connector / Hydraulic hose nipple
