Plastic Padding
Plastic Padding -ryhmän tuotteet
Epoxy putty Plastic Padding Marine Epoxy
Plastic Padding Marine Epoxy is an effective and versatile epoxy putty for repairing damage and holes on boats, both above and below the waterline. The product forms a hard surface and is particularly suitable for underwater repairs.
Marine Epoxy is not just a putty, but a multi-purpose solution for filling, bonding, gluing and sealing. It can be used on fiberglass, wood, all metals and concrete and is excellent for joining different materials. The end result is durable and waterproof and resistant to gasoline, diesel, cleaning agents and polishes.
The putty can be applied in thick layers without the risk of shrinkage or cracking. It can be painted with both 1-component and 2-component paints as well as antifouling paints. The product does not have to be painted over.
Applications
Boat hulls above and below the water surface
Fiberglass
Wood
Metals
Concrete
Filling, gluing, sealing and joining
Features
Two-component epoxy putty
Suitable for underwater repairs
Waterproof and very durable
Resistant to fuels and cleaning agents
Can be applied in thick layers
Will not shrink or crack
Can be painted and primed
Workable after 3–6 hours of hardening
Instructions
Preparation
The surface to be repaired must be completely clean.
Remove rust, dirt, oil, grease and wax
Sand the surface with coarse sandpaper, grit 120–240.
Blend
Mix in a ratio of 1:1
Take equal amounts of base and hardener.
Mix thoroughly until the color is even.
Dissemination
First apply a thin layer by scraping to allow the compound to penetrate the sanding patterns.
Fill immediately to desired thickness
Curing begins immediately after mixing
After approximately one hour, the surface can be smoothed with a wet trowel.
The ambient temperature must be at least +5 C.
Tip
Always sand the putty before further processing.
Can be painted with 1 and 2 component paints and primer
Specifications
Product name Marine Epoxy
Volume 270 ml
Product type Two-component epoxy putty for boat repairs above and below the waterline
Suitable materials Fiberglass, wood, metal, concrete
Color Light gray
Shelf life unopened 24 months
Storage temperature 15–25 C
Store in a dry and cool place.
Protect from fire, heat sources and direct sunlight.
- Epoxy putty
- Suitable for underwater use
- Can be painted with 2C paints
Plastic Padding Chemical Metal
Plastic Padding chemical metal is an effective two-component repair compound designed to repair cracks and holes in metal, concrete and stone slabs. The product forms a highly dense, stable and durable surface that can be drilled, tapped and painted.
The composition containing metal particles gives the product excellent strength and exceptional adhesion. The mass is easy to shape, cut and sand, making it a versatile and reliable solution for demanding repair jobs. The product is also resistant to high temperatures up to 110 C.
Applications
Metal surfaces
Concrete
Stone slabs
Repair of cracks and holes
Filling, sealing and joining
Features
Two-component repair compound
Contains metal particles
Very durable and strong result
Can be drilled, tapped and painted
Easy to shape and sand
Heat resistance up to 110 C
Excellent adhesion
Instructions
Preparation
Sand the surface to be repaired carefully to remove rust and paint.
Recommended sandpaper grit 80–120
Dosage
Mix a golf ball-sized amount of putty, about 40 ml.
Add 3–4 cm of hardener, or approximately 2–4 percent.
Mix thoroughly until the mixture is smooth and free of air bubbles.
Use protective gloves and goggles.
Close the filler and hardener packages immediately after dispensing.
Dissemination
Apply with a steel trowel in a scraping motion to allow the compound to penetrate the sanding marks.
Fill to desired thickness
After hardening, sand with coarse sandpaper, grit 80–120.
The best working temperature is above +20 C.
Curing time
Approximately 20–36 minutes at +20 C
Purifying
Clean tools with acetone or cellulose solvent immediately after use
Things to note
Grease, oil and silicone prevent the product from sticking
Clean sanded aluminum and galvanized steel must be cleaned before application.
- For repairing metal and concrete
- Heat resistant
- Can be drilled and tapped
Plastic Padding fiberglass screed
Plastic Padding fiberglass filler is a fast-curing and highly durable repair compound for filling large holes and cracks in fiberglass and metal. The product hardens in approximately 20–30 minutes at +20 C and is suitable for demanding repair work on boats and other structures.
The fiberglass-reinforced filler creates a strong and tight finish. It is an excellent choice for repairing boat hulls and fiberglass structures, and can also be used to repair large holes and dents in car bodies. The product has excellent adhesion to metal, wood and hard plastic.
Applications
Boat hulls
Fiberglass structures
Large holes and cracks in fiberglass
Metal surfaces
Car body damage
Hard plastic and wood
Features
Fiberglass reinforced repair compound
Suitable for large damage
Fast curing
Very durable and tight finish
Good adhesion to many materials
Instructions
Preparation
Sand the surface to be repaired carefully.
Remove rust and paint completely
Dosage
Mix a golf ball-sized amount of the compound, approximately 40 ml.
Add 3–4 cm of hardener, or approximately 2–4 percent.
Mix thoroughly until the mixture is smooth and free of air bubbles.
Use protective gloves and goggles.
Close the packages immediately after dispensing.
Dissemination
Spread with a steel trowel so that the compound also penetrates the sanding patterns.
Fill to desired thickness, maximum 5 mm
Let it harden and roughen with sandpaper grit 80–120.
The best working temperature is around +20 C.
Curing time
Approximately 20–30 minutes at +20 C
Purifying
Clean tools with ethyl acetate immediately after use
Things to note
Grease, oil and silicone prevent the product from sticking
Steel, aluminum and galvanized steel must be sanded and degreased before application.
- Fiberglass reinforced
- Easy to shape and apply
- For deeper repairs
Plastic Padding Repair Kit
The Plastic Padding repair kit is a versatile and comprehensive solution for repairing plastic boats, surfboards, snowmobiles and ski boxes. The kit is especially suitable for ABS plastic, epoxy and polyester as well as fiberglass. It works great for repairing cracks and damage and for joining different materials.
Applications
Plastic boats
Surfboards
Snowmobiles
Ski boxes
Fiberglass plastic
Steel and galvanized steel
Aluminum
Package contents
250 ml polyester
8 g hardener
2500 cm² of fiberglass mat
Plastic spatula
Brush
Mixing cup
Features
All in one repair kit
Two-component polyester resin
Suitable for repairing cracks and damage
Excellent adhesion to various materials
Also suitable for joining materials
Instructions
Preparation
The repair area must be dry, clean and free of grease.
Remove rust and paint
Roughen the surface with sandpaper.
When repairing a hole, sand the area approximately 2–3 cm around the hole.
Fiberglass mat preparation
Cut a piece of fiberglass mat that covers the damage.
The mat should extend approximately 2 cm beyond the damaged area.
Polyester blend
Pour polyester into a mixing cup
Add hardener in a ratio of 5–7 cm hardener to 50 ml polyester
Mix thoroughly with a plastic spatula until smooth.
Use protective gloves and goggles.
Ensure good ventilation
Dissemination
Apply a thin layer of polyester filler with a brush
Place the fiberglass mat in place
Saturate the carpet immediately with polyester
If necessary, apply several layers wet or after the previous one has hardened.
New layers must be applied within 12 hours or the surface must be re-primed.
Plastic Padding fillers or gelcoat can be used to finish a smooth surface.
Curing time
Approximately 25–30 minutes at +20 C
At temperatures below +10 C, curing can be accelerated with heat.
Cleaning tools
Clean tools with acetone or cellulose thinner before curing
Specifications
Product name Repair kit
Product type Two-component polyester resin
Color Yellow
Shelf life unopened 2 years
Storage temperature 15–25 C
Store in a dry and cool place.
Protect from fire, heat sources and direct sunlight.
- Complete repair kit
- All in one package
- For ABS, epoxy and polyester
Gelcoat Filler putty for gelcoat
High quality putty for gelcoat surfaces and minor damage. The product is excellent for repairing gelcoat surfaces on boats and can also be used to repair minor damage to enamel and sanitary porcelain.
Gelcoat Filler is a two-component polyester filler that stands out for its good mechanical properties and high durability in varying weather conditions. It forms a durable and shiny surface that is easy to sand, polish, wax and paint in the desired color. The end result is waterproof and long-lasting.
Applications
Boat gelcoat surfaces
Surfboards
Plastic baskets
Enamel surfaces
Sanitary ware
Features
Two-component polyester putty
Suitable for minor damage
Durable and weatherproof result
Easy to sand and finish
Can be painted and polished
Waterproof surface
Instructions
Preparation
Rinse the surface clean of salt and impurities with fresh water at high pressure
Let the surface dry.
Sand the surface smooth with sandpaper grit 100–240.
Remove dust by brushing and clean with a degreaser
Dosage
Mix a quantity of putty about the size of a golf ball, i.e. approximately 40 ml.
Add 3–4 cm of hardener, or about 2 percent.
Mix thoroughly until the mixture is smooth and free of air bubbles.
Use protective gloves and goggles.
Close the putty and hardener immediately after dispensing to prevent drying.
Dissemination
Spread with a steel trowel so that the compound also penetrates the sanding patterns.
Fill to desired thickness, maximum 3 mm
Let it harden and sand with coarse sandpaper, grit 240–800.
Finish with finer sandpaper, grit 800–1200
The best working temperature is around +20 C.
Curing time
Approximately 40–60 minutes at temperatures above 20 C
Purifying
Clean tools with ethyl acetate immediately after use
Things to note
Grease, oil and silicone completely prevent the product from sticking
- Fiberglass reinforced
- Easy to shape and apply
- For deeper repairs
Plastic Padding Marine Filler
Plastic Padding Marine Filler is an easy-to-use polyester filler specially developed for boating and marine applications. It is ideal for repairing holes and cracks above the waterline in fiberglass reinforced plastic, steel and aluminum. Once dry, the filler is easy to sand, machine, drill, tap and polish, making it a versatile solution for boat repair and maintenance.
The product can be used both indoors and outdoors.
Applications
Boat hulls and structures above the water surface
Fiberglass reinforced plastic
Steel
Aluminum
Indoor and outdoor use
Features
User-friendly polyester screed
Developed for marine use
Easy to sand and finish
Can be drilled and tapped
Suitable for a variety of repair jobs
Instructions
Preparation
Clean and sand the repair surface carefully.
Remove rust and paint
Recommended sandpaper grit 80–120
Dosage
Mix a quantity of putty about the size of a golf ball, i.e. approximately 40 ml.
Add 3–4 cm of hardener, or about 2 percent.
Mix thoroughly until the mixture is smooth and free of air bubbles.
Use protective gloves and goggles.
Close the packages immediately after dispensing.
Dissemination
Spread with a steel trowel so that the compound penetrates the sanding patterns.
Fill to desired thickness, maximum 3 mm
Let it harden and roughen with sandpaper grit 80–120.
Finish with sandpaper grit 120–320
The best working temperature is above +20 C.
Curing time
Approximately 20–35 minutes at temperatures above +20 C
Purifying
Clean tools with ethyl acetate or cellulose thinner immediately after use
Things to note
Grease, oil and silicone completely prevent the product from sticking
Steel, aluminum and galvanized steel must be sanded and degreased before application.
- For repairs above the water level
- Easily sandable polyester putty
- Can be painted over
Plastic Padding fiberglass batt
Plastic Padding fiberglass batting is an effective and fast-curing repair compound for filling large holes and cracks in fiberglass and metal. The product hardens quickly, in approximately 20–30 minutes at a temperature of +20 C, and is excellent for demanding repair work.
The fiberglass reinforced base coat creates a very durable and sturdy finish. It is an ideal choice for repairing boat hulls, fiberglass bodies and other high-strength applications. The product can also be used to repair large holes and dents in car bodies. Excellent adhesion to metal, wood and hard plastic.
Applications
Boat hulls
Fiberglass baskets
Large holes and cracks in fiberglass
Metal surfaces
Car body damage
Hard plastic and wood
Features
Fiberglass reinforced repair compound
Suitable for large damage
Fast curing
Very durable result
Good adhesion to many materials
Instructions
Preparation
Sand the surface to be repaired carefully.
Remove rust and paint completely
Dosage
Mix a quantity of putty about the size of a golf ball, i.e. approximately 40 ml.
Add 3–4 cm of hardener, or approximately 2–4 percent.
Mix thoroughly until smooth and free of air bubbles.
Use protective gloves and goggles.
Close the packages immediately after dispensing.
Dissemination
Spread with a steel trowel so that the compound penetrates the sanding patterns.
Fill to desired thickness, maximum 5 mm
Let it harden and roughen with sandpaper grit 80–120.
The best working temperature is around +20 C.
Curing time
Approximately 20–30 minutes at +20 C
Purifying
Clean tools with ethyl acetate immediately after use
Things to note
Grease, oil and silicone prevent the product from sticking
Steel, aluminum and galvanized steel must be sanded and degreased before application.
Fiberglass reinforced
Easy to shape and apply
For deeper repairs
