Primers
With high-quality primers, you create an adhesive surface for topcoats and, if necessary, also a waterproof surface below the waterline.Tuoteryhmät
Primers -ryhmän tuotteet
Hempel Light Primer is a solvent-based, 2-component, thick-film epoxy paint that provides strong and durable protection for fiberglass, steel, aluminum and plywood surfaces. It creates an effective moisture barrier on the boat hull and prevents rust formation. An excellent anti-rust paint, especially suitable for use above and below the waterline.
Product description:
Hempel Light Primer is designed to form a hard, abrasion, water and fuel resistant surface. Its thick film provides protection against corrosion and effectively prevents rust formation. Recommended for use above and below the waterline on a variety of boats.
Run:
Brush application: 6 hours
Spray painting: 2 hours (at 20°C)
Mixing ratio: 2:1 (Base 45559 : Hardener 95360)
Product safety:
Flash point: 24°C [75°F]
VOC content, mixed product: EU 434 g/L [3.62 lb/US gal]
More detailed information is available on Hempel's website.
Surface Preparation:
Remove oil, grease and dirt with a suitable detergent.
Use Hempel Pre-Clean.
Unpainted surface: Sand the surface and remove dust.
Plywood: Seal the dry and clean surface with wood pore varnish.
Steel: Remove salt and contaminants by cleaning with fresh water. Remove rust and loose material by blast cleaning or wire brushing. Remove dust.
Stainless steel, aluminum and other non-ferrous metals: use non-metallic blasting media (corundum, granite, etc.).
Application method:
Brush/Roller: Thin by 5% if necessary. Not applicable.
Airless spray: Thin 5%, nozzle pressure 175 bar [2500 psi], recommended tip: 0.019-0.023".
Film thickness:
Recommended dry 100 microns [3.9 mils], wet 200 microns [7.9 mils].
Painting conditions:
Apply only to a dry, clean surface with a temperature at least 3°C ??[5°F] above the dew point.
Surface temperature must be above 10°C [50°F] during application and curing.
The relative humidity must be below 85% during drying and curing.
Drying and Overpainting:
Touch dry 6 hours (10°C) / 3 hours (20°C)
Hard dry 12 hours (10°C) / 6 hours (20°C)
Overcoating times:
Hempel Underwater Primer 26030: 2 hours - 8 hours
Hempel Silic One Tiecoat: 65 min - 4 hours
Hempel Nexus II 27400: 8 hours - 63 hours
Storage:
Shelf life: 36 months
Storage conditions: Maximum 35°C [95°F], protected from direct sunlight, rain and snow.
Hempel's Light Primer provides reliable and long-lasting protection for your boat's hull. Choose Hempel and ensure the best possible durability for your boat.
Safety data sheet:
- 2-component primer
- Suitable for fiberglass, steel, aluminum and plywood surfaces.
- Forms an effective moisture barrier.
- Excellent anti-rust paint.
- Used above and below the waterline.
Kampanja
Hempel Underwater Primer is a fast drying underwater primer containing aluminium flakes. It can be used as a sealer over old antifouling or as an adhesion primer over epoxy primed surfaces before applying antifouling.
Recommended use:
Can be used on fiberglass, wood and steel surfaces. Suitable for use in all areas below the waterline including keels.
Product safety:
Flash point: 35°C [95°F]
VOC content: 479 g/L [4.00 lb/US gal]
Handling:
Handle with care. Read all warnings on packaging and paint containers before use.
Follow local and national regulations. Always refer to the Hempel Material Safety Data Sheet for more detailed product information in addition to the product data sheet.
Product information:
Product code: 26031
Standard shade/code: Aluminum gray 19000
Dry matter content: 39 ± 2%
Specific gravity: 1.2 kg/L [10 lb/US gal]
Purity:
Remove oil, grease and other contaminants with a suitable detergent.
Clean with Hempel Pre-Clean.
New building:
Unpainted surface: Sand the surface and remove dust.
New wood: Impregnate a dry and clean surface with a suitable wood impregnation agent and let dry.
Steel: Remove salt and other contaminants by cleaning with (high pressure) fresh water. Remove all rust and loose material by blast cleaning or wire brushing. Remove dust.
Maintenance and repair:
Previously treated surface: Sand, clean and dry the surface.
Spot paint and sand to achieve a uniform surface profile. For further information, see Hempel's separate Surface Preparation Instructions publication.
Diffusion:
Thinner: Hempel Thinner 811
Cleaning agent: Hempel Thinner 811
Application method:
Roller: 20%
Brush: 20%
Painting pad: 20%
Airless sprayer: 20%
Nozzle pressure: 200 bar [2900 psi]
Recommended nozzle: 0.018-0.021'
Keep thinning to a minimum. The product can be applied by spray. Contact Hempel for further information. Spraying data is for guidance only and is subject to change. Pressure is given at a material temperature of 20 °C [68 °F].
Film thickness:
Specification range: Low, High, Recommended
Film thickness, dry: 50 microns [2.0 mils]
Film thickness, wet: 130 microns [5.1 mils]
Theoretical coverage: 7.8 m²/L [320 sq ft/US gal]
Avoid using a film that is too thick to ensure best performance.
Painting conditions:
Apply only to a dry, clean surface that is at least 3°C ??[5°F] above the dew point to avoid condensation.
The relative humidity must be below 85% during drying and curing.
Notes:
Mix well before use.
Safety data sheet:
- Fast-drying underwater primer
- Does not form a waterproof membrane
- Works well as a bonding paint
- Works as a primer only for 1-K paints
Kampanja
Make a smooth transition from traditional antifouling to Hempel's advanced biocide-free antifouling protection with Hempel's Conversion Primer. This two-component epoxy allows for an easy transition from old surfaces to a newer form of protection. Use as a bonding primer between epoxy-primed surfaces and Hempaspeed TF.
Product description:
Hempel's Conversion Primer is specifically designed to provide a reliable adhesion base for Hempel's biocide-free products. It can be applied over old, good quality antifouling coatings and provides optimal adhesion for new protection products.
Product safety:
Flash point: 31°C [88°F]
VOC content, mixed product: EU 543 g/L [4.53 lb/US gal]
More detailed information is available on Hempel's website.
Instructions:
Remove oil, grease and other contaminants with a suitable detergent.
Apply over the old antifouling coating to ensure good adhesion.
Use as an adhesion primer between an epoxy primed surface and Hempaspeed TF.
Product information:
Gloss: Matte
Dry matter content: 36 ± 2%
Dry film thickness, reference: 25 microns [1.0 mils]
Application method:
Mixing ratio Base 45445 : Hardener 95441 (3 : 1 by volume).
No thinning.
Operating time 8 hours.
Overpainting:
Recommended products for topcoating: Hempel's Silic One Tiecoat, Hempaspeed TF.
Drying time:
Surface temperature 10°C [50°F]: Sand-dry in 2½ hours, fully cured in 14 days.
Surface temperature 20°C [68°F]: Sand-dry in 1¼ hours, fully cured in 7 days.
Surface temperature 30°C [86°F]: Sand-dry in ½ hour, fully cured in 4 days.
Hempel's Conversion Primer provides an excellent transition base, ensuring durable and effective protection for your boat. Choose Hempel and take a step towards a biocide-free future.
Safety data sheet:
- Two-component epoxy
- Suitable over old anti-fouling paint
- Switch from traditional antifouling to Hempel's advanced biocide-free antifouling coating
- Coverage 15m2/L
Kampanja
Hempel's Conversion Primer is specifically designed to provide a reliable adhesion base for Hempel's biocide-free products. It can be applied over old, good quality antifouling coatings and provides optimal adhesion for new protection products.
Product safety:
Flash point: 31°C [88°F]
VOC content, mixed product: EU 543 g/L [4.53 lb/US gal]
More detailed information is available on Hempel's website.
Instructions:
Remove oil, grease and other contaminants with a suitable detergent.
Apply over the old antifouling coating to ensure good adhesion.
Use as an adhesion primer between an epoxy primed surface and Hempaspeed TF.
Product information:
Gloss: Matte
Dry matter content: 36 ± 2%
Dry film thickness, reference: 25 microns [1.0 mils]
Application method:
Mixing ratio Base 45445 : Hardener 95441 (3 : 1 by volume).
No thinning.
Operating time 8 hours.
Overpainting:
Recommended products for topcoating: Hempel's Silic One Tiecoat, Hempaspeed TF.
Drying time:
Surface temperature 10°C [50°F]: Sand-dry in 2½ hours, fully cured in 14 days.
Surface temperature 20°C [68°F]: Sand-dry in 1¼ hours, fully cured in 7 days.
Surface temperature 30°C [86°F]: Sand-dry in ½ hour, fully cured in 4 days.
Hempel's Conversion Primer provides an excellent transition base, ensuring durable and effective protection for your boat. Choose Hempel and take a step towards a biocide-free future.
Safety data sheet:
- Two-component epoxy
- Suitable over old anti-fouling paint
- Switch from traditional antifouling to Hempel's advanced biocide-free antifouling coating
- Coverage 15m2/L
Kampanja
Hempel's High Protect II is a high performance solvent-free epoxy paint specifically designed for anti-osmosis and repair applications. This two-component system offers easy application and forms a durable, water-repellent surface. Suitable for fiberglass and steel below the waterline.
Product description:
Hempel's High Protect II is a solvent-free epoxy paint that provides effective protection against osmosis and repair. Its properties make it an ideal choice for priming fiberglass and steel boats below the waterline.
Features:
Solvent-free anti-osmosis and repair paint.
Easy to apply and forms a durable surface.
Suitable for fiberglass and steel below the waterline.
Run:
45 minutes (at 20°C).
Mixing ratio:
3:2 (Base 35789 : Hardener 95078).
Product safety:
Flash point: 129°C [264°F]
VOC content, mixed product: EU 34 g/L [0.28 lb/US gal]
Surface Preparation:
Remove oil, grease and other contaminants with a suitable detergent.
Unpainted surface: Sand the surface and remove dust.
Steel: Remove salt and other contaminants by cleaning with fresh water. Remove rust and loose material by blast cleaning or wire brushing. Remove dust.
Application method:
Brush/Roller: No thinning.
The product can be applied by spray. Contact Hempel for more information.
Film Thickness: Recommended dry 150 microns [5.9 mils], wet 150 microns [5.9 mils].
Painting conditions:
Surface temperature above 10°C [50°F] during application and curing.
Relative humidity below 85% during drying and curing.
Drying and Overpainting:
Touch dry in 45 minutes (20°C).
The overcoating time depends on the conditions and should be checked as necessary.
Overcoating times:
Topcoat with recommended products such as Hempel's Underwater Primer 26030 or Hempel's Light Primer 45550.
Storage:
Shelf life: Base 36 months, Hardener 24 months.
Store in accordance with local regulations at a maximum temperature of 35°C [95°F], protected from direct sunlight, rain and snow.
Applications:
Fiberglass and steel boats below the waterline.
Hempel's High Protect II offers reliable protection and ease of use for osmosis prevention and repair. Choose Hempel to ensure your boat's durability and protection in demanding conditions.
Safety data sheet:
- 2-component primer
- Solvent-free anti-osmosis and repair paint.
- Easy to apply and forms a durable surface.
- Suitable for fiberglass and steel below the waterline.
Hempel's Primer Undercoat is a fast-drying, high-coverage undercoat and intermediate coat, designed to ensure durability and surface stability in preparation for topcoating with single-component topcoats.
Recommended use:
On fiberglass, wood and steel surfaces.
For indoor and outdoor use above the waterline.
Features:
Very opaque.
Quick-drying.
Product safety:
Flash point: 40°C [104°F].
VOC content (389 g/L): Meets EU requirements.
Handling:
Handle with care. Follow the warning and safety labels on the packaging and paint containers.
Follow local and national regulations during use.
Product information:
Product code: 13201
Standard shade/code: White 10000
Dry matter content: 49 ± 2%
Specific gravity: 1.3 kg/L [11 lb/US gal]
Dry film thickness, reference: 40 microns [1.6 mils]
Surface preparation:
Remove oil, grease and other contaminants with a suitable detergent.
New building:
Unpainted surface: Sand the surface and remove dust.
New wood: Impregnate a dry and clean surface with a suitable wood impregnation agent and let dry.
Steel: Remove salt and other contaminants by cleaning with (high pressure) fresh water. Remove all rust and loose material by blast cleaning or wire brushing. Remove dust.
Maintenance and Repair: Previously treated surface - Sand, clean and dry the surface. Touch up and sand to achieve a uniform surface profile.
Diffusion:
Thinner: Hempel's Thinner 811 08111.
Application method and tool: Brush, roller, Paint Pad or airless sprayer.
Thinning max. volume 10% brush, roller, Paint Pad; 15% airless spray.
Film thickness, dry: 40 microns [1.6 mils].
Film thickness, wet: 80 microns [3.1 mils].
Theoretical coverage: 12 m²/L [490 sq ft/US gal].
Painting conditions:
Apply only to a dry and clean surface with a temperature at least 3°C ??[5°F] above the dew point, avoiding condensation.
The relative humidity must be below 85% during drying and curing.
Drying and Overpainting:
Touch dry hours: 3 (20°C [68°F]), 6 (10°C [50°F]).
Sanding dry hours: 24.
Overpainting: All masking tape used during paint application must be removed while the coating is still wet.
Notes on overpainting:
If the maximum overcoating time has been exceeded, the surface must be roughened to ensure adhesion.
Product descriptions for other products:
Next possible coat of paint:
Hempel's Multicoat
Hempel's Brilliant Gloss
Hempel's Non-Slip Deck Coating
Storage:
Shelf life: 60 months from date of manufacture in unopened original packaging.
Storage conditions: Store in accordance with local regulations.
Safety data sheet:
- 1-component primer
- Suitable for fiberglass, wood and steel surfaces.
- Works great as a bonding paint
- Very opaque
- Quick-drying
Kampanja
Anti-corrosion paint for various substrates. Recommended as a primer for sterndrives and propellers. Adheres well to steel and other metal surfaces. Dries quickly and is easy to paint. Forms a matt finish. Excellent primer for Hempel's Ecopower Prop sterndrive paint. Minimum application temperature 5°C
- 1-component spray primer
- Suitable for Hempel Ecopower prop paint
- For steel and other metal surfaces
Kampanja
2K epoxy solution colorless 2-component, low viscosity and very good absorption epoxy solution. Used on wood and other porous surfaces as the 1st layer before painting. Not to be used on gelcoat surfaces. Used both below and above the waterline. Pot life: 8 hours at 20°C. Mixing ratio: 4 : 1 Lowest application temperature 5°C.
Safety data sheet:
- 2-component solution
- Suitable for wooden surfaces
- Below the waterline
Kampanja
Silicone-based, moisture-curing adhesion primer for Hempel's Silic One. Ensures adhesion between Hempel's Light Primer or Hempel's Conversion Primer and Hempel's Silic One. The product is used to prevent vegetation from adhering to fiberglass, steel and aluminum boats. For use below the waterline.
Safety data sheet:
- 1-component
- Adhesion paint for Silic One paint
- Light Primer or Coversion primer over paint
- Below the waterline
Kampanja
B-Free Conversion Coat is a two-component epoxy paint that seals a traditional primer prior to painting with the B-Free system. It can be used over existing traditional primer when it is in good condition and provides a stable base for the B-Free Tiecoat. Only one coat is needed for a smooth transition from traditional primer to B-Free. B-Free Conversion Coat is compatible with most traditional primers and there is no need to remove the old primer.
- 2-component
- B-Free Explore for paint
Kampanja
Outlet
Alkyd-based semi-gloss anti-rust paint. Primer and topcoat in one product. Adheres well to iron, steel, aluminum, galvanized and galvanised surfaces. Coverage: 7.5 m2/0.75 ml.
- 1-component
- Suitable for iron, steel and aluminum
- Semi-gloss anti-rust paint
Alkyd-based semi-gloss anti-rust paint. Primer and topcoat in one product. Adheres well to iron, steel, aluminum, galvanized and galvanised surfaces. Coverage: 7.5 m2/0.75 ml.
- 1-component
- Suitable for iron, steel and aluminum
- Semi-gloss anti-rust paint
Fast-drying, 2-component epoxy primer for gelcoat. Protects against plastic rot. Can be painted at +5 °C. As an adhesion primer for painting roughened decks. Contains hardener.
Why primer? Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, pore filling and water penetration of paints. Primer is the first complete coat of paint on a boat's surface. Primers are designed to adhere well to new surfaces and are formulated to meet the specific needs of each surface.
Available in two different packaging sizes, choose the most suitable size from the drop-down box:
Outlet:
- Quick-drying
- 2-component epoxy primer for gelcoat
- Protect against plastic pollution
- Can be painted at temperatures of +5 °C
- Contains hardener
- Suitable materials: Gelcoat
Why primer? Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, pore filling and water penetration of paints. Primer is the first complete coat of paint on a boat's surface. Primers are designed to adhere well to new surfaces and are formulated to meet the specific needs of each surface.
Available in two different packaging sizes, choose the most suitable size from the drop-down box:
- 750ml
- 2.5 liters
- 5.0 liters
Outlet:
- 20.3 m2 / 2.5 l
- 40.6 m2 / 5.0 l
- 6 m2 / 0.75 l
- 2-component epoxy primer for gelcoat
- Color: gray
- Quantity: 750ml, 2.5L, 5.0L
- Surface/gloss: matte
Fast-drying, 2-component epoxy primer for gelcoat. Protects against plastic rot. Can be painted at +5 °C. Contains hardener.
- Quick-drying
- 2-component epoxy primer for gelcoat
- Protect against plastic pollution
- Can be painted at temperatures of +5 °C
- Contains hardener
- Suitable materials: Gelcoat
Why primer? Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, and pore filling of paints. Primer is the first complete coat of paint on a boat's surface. Primers are designed to adhere well to new surfaces and are formulated to meet the specific needs of each surface.
Available in two different packaging sizes, choose the most suitable size from the drop-down box:
- 750ml
- 2.5L
Outlet:
20.3 m2 / 2.5 l- 6 m2 / 0.75 l
- 2-component epoxy primer for gelcoat
- Suitable for Gelcoat
- Color: green
- Quantity: 750ml, 2.5L
- Surface/gloss: matte
- Adhesion primer for painting roughened decks
2-component epoxy primer for steel, light metal and plywood. Easy to apply, fast drying, no sanding required between coats. Excellent anti-corrosion properties. Adhesion primer between previously painted epoxy primer and hard anti-fouling paint. Contains hardener.
- 2-component epoxy primer For steel, light metal and plywood
- Easy to apply, quick drying
- No sanding required between coats
- Excellent anti-rust properties
- Adhesion primer between previously painted epoxy primer and hard antifouling paint
- Contains hardener
Why primer? Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, and pore filling of paints. Primer is the first complete coat of paint on a boat's surface. Primers are designed to adhere well to new surfaces and are formulated to meet the specific needs of each surface.
Available in two sizes:
- 750ml
- 2.5L
Outlet:
6 m2/0.75 l- 20.3 m2/2.5 l
- 2-component epoxy primer
- Suitable for steel, light metal and plywood
- Color: gray
- Quantity: 750ml, 2.5L
- Surface/gloss: matte
- Area of ??use: above and below the waterline
2-component epoxy primer for steel, light metal and plywood. Easy to apply, fast drying, no sanding required between coats. Excellent anti-corrosion properties. Adhesion primer between previously painted epoxy primer and hard anti-fouling paint. Contains hardener.
- 2-component epoxy primer For steel, light metal and plywood
- Easy to apply, quick drying
- No sanding required between coats
- Excellent anti-rust properties
- Adhesion primer between previously painted epoxy primer and hard antifouling paint
- Contains hardener
Why primer? Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, pore filling and water penetration of paints. Primer is the first complete coat of paint on a boat's surface. Primers are designed to adhere well to new surfaces and are formulated to meet the specific needs of each surface.
Available in two sizes:
- 750ml
- 2.5L
Outlet:
6 m2/0.75 l- 20.3 m2/2.5 l
- 2-component epoxy primer
- Suitable for steel, light metal and plywood
- Color: gray
- Quantity: 750ml, 2.5L
- Surface/gloss: matte
- Area of ??use: above and below the waterline
Kampanja
Primer and undercoat combination for 1-component topcoats. Intended for use above the waterline with 1-component topcoats and topcoats. A premium system in combination with International topcoats and topcoats.
Why primer?
Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, pore filling and water penetration of paints. Priming is the first complete coat of paint on a boat's surface. Priming is designed to adhere well to new surfaces and is formulated to meet the specific needs of each surface.
- 1-component primer
- Thinning: Thinner Nr 1 / Thinner Nr 100
- International topcoat primer
- Primer and base coat
- Do not use under 2-component paints
- Coverage: 9.0m2/L
- Number of layers: 2-4
- Application method: brush/roller
- One-component primer for wood, steel and aluminum below the waterline. Also as an insulating layer when changing antifouling paint. Coverage is 5.6 m2/ 0.75 liters and 18.5 m2/ 2.5 liters.
1-component primer for below the waterline - Quick-drying
- Anti-rust primer for metal or wood
- Adhesion primer used as an intermediate primer for colors that cannot otherwise be combined
- Suitable for use below the waterline, as a base primer or as an intermediate primer between unknown paints (If you don't know what paint was used previously? ->Primacon can be painted over all old paints.)
- Suitable materials: Gelcoat, wood, steel, aluminum, lead, carbon fiber
Why primer? Priming creates protection against osmosis and corrosion. It improves the adhesion, coverage, pore filling and water penetration of paints. Primer is the first complete coat of paint on a boat's surface. Primers are designed to adhere well to new surfaces and are formulated to meet the specific needs of each surface.
Available in two sizes:
750ml- 2.5L
| Recommended number of layers: | Thinner |
| High-pressure sprayer | 1-5 | No. 3 |
| Brush | 1-5 | No. 3 |
| Roll | 1-5 | No. 3 |
- 1-component
- Suitable for Gelcoat, wood, steel, aluminum, lead and carbon fiber
- Below the waterline
- Color: gray
- Lowest painting temperature: + 10
- Highest painting temperature: + 29
- Theoretical coverage (m2 per liter): 7.4
- Area of ??use: below the waterline
- Suitable for above the waterline: No
International Propeller Primer is a fast-drying, 1-component primer formulated specifically for use on outboard motors, propellers and sterndrives. Propeller Primer adheres to surfaces with excellent adhesion thanks to Dual Activated bonding technology. Combined with our recommended International antifouling paint, it forms a uniform topcoat that resists dynamic and cavitation forces, protecting propellers and underwater metals from fouling. 250 ml.
- Best-in-class paint with International antifouling paint
- Excellent adhesion to many underwater metals
- Water-based, low-odor primer that is easy to apply with a brush
- 1-component primer
- Suitable for drives, outboards and propellers
- Thinner: do not thin
Anti-rust primer for extreme conditions. Long-lasting anti-rust effect.
- 1-component primer
- Suitable for new or heavily oxidized surfaces
- A rust inhibitor that can be applied over many different types of 1- and 2-component paints: polyurethane, epoxy, rubber, automotive paint...
- Excellent for harsh climatic conditions (corrosive gases, marine conditions, etc.), withstands temperatures up to +175ºC
